Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP1453	After turning on the TV, a line appeared on the screen and it turned off.	High power supply above 108 v	I replaced the 120k r 919 and everything was normal	ELETRONICA ROCHA
PHILCO	PCM-2046	It would turn on, the LED would flash, r720 was damaged, it would be replaced and it would burn again.	O problema era ic 601 tda-3653b	Changing it solved the problem, thanks	Eronaldo
PHILCO	PSC 2952 N	When it turns on from high voltage and turns off	Changed the weak c - 712 6 k 8 / 1600volts		jaironuness
PHILCO	PCM-1466	Image distorts in some channels	Changed c- 205 2.2/50 volts weak		jaironuness
PHILCO HITACHI	PC 1441	The TV turns on and within seconds the vertical closes	Solution to the problem r 725 r 4r7 close to the flay back		FRANCISCO IVAN BASÍLIO - Ibiara - PB
PHILCO	14CT6401	Ripples at 110v	Altered waveform	Replace font scrs	paulo artur rio de janeiro
PHILCO	PC 1427 U	Whistle when turned on, but inoperative	Power supply did not arm due to deficiency in filter component	Replace cap906,909,and diode905	paulo artur rio de janeiro
PHILCO	PCM 1448	Turning off by itself	Dz 904 short		paulo artur rio de janeiro
PHILCO	TP 14U56 ***	No image check if there is power on the filament, when the screen increases it turns very faint white check if there is 180v in cap.c-713 if ok, note: rgb circuit must have 180v	Replace shock absorber		wagner
PHILCO	PCM 1443 EMOTION ***	Turning off white screen and retraces	R-715 c-719	R-715 1r,subs 4r7 c-719 10mf x 350v	wagner
PHILCO	TPF2130	Does not turn on, without +14v pin 1 ic905	Solda fria r931 18r 2w		BETO2828
PHILCO	PCS 2078 NãO MARCA	Bu 2508 dx shorts out	C730 5k6 1kv6 changed and change original bu 2508 dx and increase c715 to 7k5*2kv		luiztvsom
TV PHILCO	PCM 2046	Luminance-	Replaced the c716 10 / 250 volts	TV worked normally.	jaironuness
PHILCO	TP-2053	TV doesn't work std-by light blinks continuously but dimly	Changed the vertical output tda9309		jaironuness
PHILCO	TP-1452N	When turning on there is no sound after a while the sound starts to come back hoarse.	Change the audio output		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP-1452	TV with normal power supply, when turned on it generates and cuts in 1 second	Check r713 of 1k8 changed		Daniel
PHILCO	PC 20R42	Interference on the screen without video TV has sound	Exchange c301 0.47/35 votes		jaironuess
PHILCO	PC- 20R42 **	TV out of horizontal frequency	Or capacitor 303 of 47/35 votes was exhausted		jaironuness
PHILCO	TPF 2941	It has a power supply but no gun	It fell, it was fixed, the trails worked normally; after two days it broke down, it was left alone in the waiting room		carlos branco
PHILCO	PCM2044	When the TV was turned on, the image was shaking, and when the volume was increased, the image was even more shaky.	I checked the power supply and it was normal, but when I removed the capacitor from the power supply input I realized that it had a bad, rotten leg, the 400v/220mf c905 replaced it and went for a hug		This email address is being protected from spambots. You need JavaScript enabled to view it.