Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PCM1443
|
Image blinking as if it were a stand by LED, normal frame, normal voltages, except video voltage; controls inoperative. | R713(100k) open. | Replace r713(100k), device ok. | clayton |
| PHILCO |
TP1454
|
Problem with the colors, it remains without demagnetizing the kinescope. | Check the "epcos" brand component with placement number th 901. this component is connected together with the kinescope coil. | Just replace it with another one and go for the hug!!! | FRANCISCO |
| PHILCO |
TPF-2901
CP01RL01 |
When turned on, it displays a white screen with horizontal retrace lines and seconds later it turns off. | Replacement of the 4r7 r711 that was open. | Marques | |
| PHILCO |
PCS 2700
|
The TV turns off as soon as it was turned on | This TV doesn't oscillate without the fly back and without the deflector so it would be more difficult to discover the defect. | But in this case it was the bad deflector coil that was causing the TV to turn off | heliomar |
| PHILCO |
TPF 2130
CP 03 |
Does not turn on, there is no + 14 vdc pin 1 of ic 905 | Change c 918 open | CARLOS ROCHA | |
| PHILCO |
PCS-2976
|
Actuated protection It is with very high voltage | C715 or c730 changed | Henry Moura | |
| PHILCO |
PCS 3322N
CP 01 LR02 |
When turning off the power, it no longer turns on, only flashes, the power supply does not arm | Next to the wide capacitor switch c728 3n3 x 1600v | C728 3n3 x 1600v | |
| PHILCO |
PCM2976
|
TV turns on after + or - 30 seconds, threatens to close the horizontal and turns off. | Probable cause, open power supply diode d917. | amsmariano | |
| PHILCO |
PCM-2046
|
Jagged image | Interference on the kinescope PCI flat | Move the kinescope PCI flat away from the flay back as much as possible. | Wender |
| PHILCO |
DVT 100
|
Doesn't spin the disc | R 23 of 1 r | Replace r 23 of 1 r | |
| PHILCO |
PCS2952N
|
Low power supply hitting the power supply transformer | Diode in4148 901 open | julio itaguai | |
| PHILCO |
TP2054
|
When the TV was turned on, it started to show high voltage and then turned off and did not oscillate | I turned off +b from the flay back and the TV oscillated normally with the 109v input but if I turned on +b it stopped oscillating. | I tested the flay back in my test and it was bad without discharge, I replaced it and everything was fine | |
| PHILCO PLATINUM |
TP1452N
|
Does not turn on, inoperative, low voltage and oscillating on the horizontal transistor collector. | Change 1uf x 100v electrolytic located in the power supply. | FRANCISCO
|
|
| PHILCO |
TP1452
|
Power supply pulsing, inoperative. | Check the 1uf x 100v electrolytic capacitor at the power supply. Just replace it with another one. | FRANCISCO
|
|
| PHILCO |
PCS2976S
|
Horizontal closing on the sides | 150k resistor near d irf ,n fir horizontal plate swap | Replace everything resolved | MARCOS MELO CASCAVEL CE |
| PHILCO |
PCR2049
CPH06 |
Turns it on after a few minutes, it turns off or you turn it off, then it doesn't turn on anymore, it only turns on after a few minutes. | I verified that the horizontal output was experiencing unusual heat. | I replaced the 708 capacitor (471x2kv) and that's it. | Alvanyr |
| PHILCO |
TP1453
CP02RO |
Philco tp 1453 TV with a drizzled image as if high voltage was escaping and switching off intermittently, I changed the flay and cleaned the capacitors horz. | R-917 2k2 | Open replace do not measure on the chassis | Schulz |
| PHILCO |
PVT1416
|
Does not turn on, power supply drops voltage when trying to turn it on or placing a load | The power supply primary capacitors c504=47/25v, c538=1/160v | BRUSKE | |
| PHILCO |
TPF2121
|
Sometimes it doesn't turn on | Resolve diode d 907 | Tip from your cÉzar | JOHNN |
| PHILCO |
TPF 2121
|
Loud noise comes out of the speaker and protects LED keeps flashing | Diode d 909 shorted r911 r912 open | JOHNN |