Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	PCS2952	Dull	The defective component was the open resistor r718 (also change the zenerzd702) a horizontal pulse is responsible for the operation of ci pin 38, fbp in	Note: I noticed that this pulse is common for all brands and models that use the ci 8361/8360/8362.	DJALMA MILAN
PHILCO	PC1443	Horizontally shrunken and vertically closed	Main cause of this problem (l701), then q901 q 904 and 905 lastly ic 101. I fixed it was l701.		Elias2305
PHILCO	2046	The TV does not tune the channel	It had 33v on the seletronic bt but it didn't have os9v on the seletronic bm so I went to the IC 701 regulator and it was ok I then discovered a broken track I built a bridge on it and it was broken		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PCM1446/2046	When the TV was turned on, it just stayed on stand by and didn't wake up or flicker.	I checked its power supply and at the output there is a 220mf/160v c911 capacitor, it was dry, it didn't even measure 1 mf, I replaced it and it worked normally		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP29C21	Fountain oscillating, making noise tick tick tick...	Replace fly-back		Scorpion
PHILCO	TP-2054	Turns it on and off, no brightness appears	Check r 910-912 0.47r diode d809	Diode short TV won't turn on	Alvaro (prolar)
PHILCO	TP1454 - 2054	Activating protection circuit and does not turn on	See if 905 shorted behind the sensor = remote
PHILCO	PCM-2144	Oscillating color	Ic 102 memoria 80011a		Alvaro (prolar)
PHILCO	PC 1425 CPH 02	Does not adjust phase	Resistor r724 de 22k no pino 11 do ic 701		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP1452N	It didn't turn on, the LED was on, when I pressed the channel button it went off and then came back on again.	I replaced the ci 101 - m37272m8-194sp and it worked great		Luiz Alberto Camargo
PHILCO	PCS-2976S	Ripple on the sides of the image	Capacitor smd c931	Replace	Alvaro(prolar)
PHILCO	PC2044	Without generation, with the LED on, normal +b voltage.	C915 almost dry 1000mf		Ramiro Lima
PHILCO	PC2043	Contrast doesn't work	O d301 with leak, r716 open		Ramiro Lima
PHILCO	PC1443	It works normally, but if it turns off and turns on at the same time, it no longer turns on and the +b remains normal.	Swap c706 22k		Ramiro Lima
PHILCO	PC1443	With a normal image, there are just no characters on the screen.	Verificar r-505,r-504,r-510,r-716, r-717,r-714,r-718,r-706,r-612,r-173,r-172,r-171,r-613, zd-601.		Ramiro Lima
PHILCO	PC1446	Without generating, with voltages all normal and LED just blinking	R705 open from 560r		Ramiro Lima
PHILCO	PC1446	Generates and cuts after 10 seconds, only 300v remains, if you release the +b, on the deflector it generates normally.	Zd-703,c-708,c-908,zd-903.replace.		Ramiro Lima
PHILCO	PCM1451	Without generates and without +b.	Tda-4605-3		Ramiro Lima
PHILCO	PC1446	Without generating but with the normal +b, the normal 20v, just doesn't reach the collector horizontal oscillator.	Tda-8360k-4x		Ramiro Lima
PHILCO	PC1444	Working with image, coming and going with drizzle without following the controls	C-719 almost dry 10mf- 350v.		Ramiro Lima