Philco Repair Tips
Search: philco
Results: 4838
Results: 4838
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PVT1416
|
Does not turn on, power supply drops voltage when trying to turn it on or placing a load | The power supply primary capacitors c504=47/25v, c538=1/160v | BRUSKE | |
| PHILCO |
TPF2121
|
Sometimes it doesn't turn on | Resolve diode d 907 | Tip from your cÉzar | JOHNN |
| PHILCO |
TPF 2121
|
Loud noise comes out of the speaker and protects LED keeps flashing | Diode d 909 shorted r911 r912 open | JOHNN | |
| PHILCO |
PCS 2976
|
Does not work at 110 vts | Replace d 918 | Get separated | ELIZEU RIBEIRO |
| PHILCO |
TP-2052N
00000 |
TV with bad tuning, image with drizzle. giving the impression that the seletronic is defective. | Filtro do if mf201 | I replaced it for one from scrap, defect resolved, hugs, I believe everyone is aware of putting their tips to everyone, professional friend | |
| PHILCO |
PCM 1452
|
TV was oscillating but the screen was dark, adjusting the screen, a squeak came on the screen with a deficiency in one color, it was all yellow | Ci one (oscillator) was defective, I replaced it, it solved the problem | ozanan | |
| PHILCO |
TPF-2121C
00000 |
Oscillates horizontally but after a maximum of 4 seconds it turns off, and the LED flashes; | Capacitor of { 6n8 1k6} as low capacitance ; | I replaced fixed braces blz!!! tec friends who are aware put their tips because everyone needs a tip shelter everyone | marcos melo |
| PHILCO |
TP2054
|
This TV was turning on but with no image, just a line in the center, I thought it was vertical and it wasn't | 917 resistor without soldering at one of its ends, after re-soldering the TV started working normally again. | Moizes | |
| PHILCO |
PCM2044
|
Fabric turns off intermittent. | C719 (10uf/250v) | Andrade Sequeira | |
| PHILCO |
PCM2044
|
Does not work. stdby led is blinking | Shorted ic 401 (tda2613) | Andrade Sequeira | |
| PHILCO |
PCM2044
|
Doesn't work | Zd901 is shorted.replace str50103. | Andrade Sequeira | |
| PHILCO |
PCM2044
|
Dark screen | R716 (10k) | Andrade Sequeira | |
| PHILCO |
PCM2044
|
Turns off every 5 minutes | D301 e d302 | Andrade Sequeira | |
| PHILCO |
PCM2044
|
No contrast | C716, r706 e r717 | Andrade Sequeira | |
| PHILCO |
PCM 2044
CPH05 |
When you increase the brightness, the TV turns off | Zd703 leak | Filipe | |
| PHILCO |
PCM 2044
CPH05 |
When connecting an antenna, the TV turns off (protection) and when the brightness increases | Leaky dz-703 (power supply) | Luiz Filipe | |
| PHILCO |
PCS 2956N
|
Power supply does not weapon | 470uf Dry Low Supply Condenser | Elizeu | |
| PHILCO |
PC2027U
|
The power supply had a sharp and loud hiss. | C911 -> 4,7uf/160v. | ||
| PHILCO |
PCS2952
|
It didn't change channels, the volume was muted and no OSD characters appeared, it just turned on and nothing else. | Ic1401-tda8425 was killing the memory sda leading to 0 volts after changing the ic1401 and ic1402-ha11508 the TV started working normally again. | ||
| PHILCO |
TP-2054
|
Dark image, however, with normal menu on screen | Zd701 with leak (near the flyback - abl line) | Easy to detect. It is to measure the voltage +b 108v, if ok, measure abl -13v (you will notice that the abl line is low) | Tec Vídeo |