Philco Repair Tips

Search: philco
Results: 4838

Make	Model	Symptom	Problem	Solution	By
PHILCO	PCM 2046	Reduced frame in four corners	Power supply all ok, micro, oscillator, vertical everything you can imagine	Direct fly back replace	Neguinho(itapevi) SAE-TAV ELETRONICA
PHILCO	PCM-2046	The TV was turning on and off quickly without stopping.	Change all the power supply capacitors and also close to the flay back (the electrolytics	Because the low microfraids of both causes the power supply to trip	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP 1554	Vertical does not stabilize and cuts image at the top, change	Change the two power supply capacitors: c914 and c 918 which filters the -12v and +12v. Don't test, change soon.		caio
PHILCO	TP1454 CPH06	TV doesn't remember, screen closed halfway down, sometimes it turns on, sometimes it doesn't turn on and when it turns on, it sometimes retracts and sometimes drizzles.	Ic102(eeprom) I just took it out, cleaned the board and put it in and it was beautiful		samuel3d
PHILCO	TP 1453	It doesn't arm (it looks like it will arm, but it doesn't). I enlarged the screen and insisted several times in a row that the image appeared and I saw the frame reduced.	Deflector coil.		Tec Vídeo
PHILCO	1453S	TV does not turn on via the keyboard or the keyboard does not work or does not work	The keyboard is certainly locked, turn on the TV with the control and go to the channel. If the user has forgotten the password, use the factory password which is 7658 and unlock the keyboard, it will definitely work.		bel araguaçu
PHILCO	TPF2121 2121	TV with feedback line turning off when changing channels closes screen	Capacitor c 715 do horizontal with low capacitance	Replace for a new one	eletronica marcos melo cascavel ce
PHILCO	PCM2044	TV turning on and off intermittently, the LED also blinks along with the TV	Go up to the resistance (r713) of 100k it may be altered		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PC-2136	No contrast.	Exchanged at r- 765- 56 k hms		jaironuness
PHILCO	PC-2046	TV only has one channel without menu functions. no characters.	I changed the ic- 101- m 37210m3-709-sp. You can put the m 37211m2-603 sp which works normally.		jaironuness
PHILCO	TPC 2910	Disarms after a few hours.	(c 805) 10mf 160v seco	Replace, for 47mf 160v it's cool!!	IGOR ALMEIDA
DVD PHILCO	DV-P4500	Goes crazy, opens drawer, goes into stop, pause mode...	C611 in open power supply or changed direct exchange		alpha eletronica
DVD PHILCO	DV-P4500	Display off	Changing d609 at the power supply is no use measuring		alpha eletronica
PHILCO	TP20V56	Power supply does not oscillate or light up stand by LED	Smd capacitor c984 in c.i. power supply oscillator		eletronica fernandes
PHILCO	TP20V56	Power supply does not oscillate or light up stand by LED	Smd capacitor c984 in c.i. power supply oscillator		eletronica fernandes
PHILCO	PCS2952	Stand by led blinking and power supply oscillating	R949 of 47Ω changed, it is on pin 7 of the t901 transformer.		eletronica fernandes
PHILCO	PCS-2956N	Turns on with high voltage, makes a few clicks and turns off	Flay-back ruim	I replaced it, it was fine.	Eronaldo
PHILCO	TP2052N	Replace these components and the device will work normally again.	Philco pcs-2976 dead, supply high (170 v) change resistor 917 (2k2) diode 908, d 902 (transistor type) ic 802 (photo-coupler)	Replace these components and the device will work normally again.	Elias
PHILCO	PC20R42	It doesn't turn on, it only lights up STBY LED, power supply ok, micro crystal ok	Reset circuit pin 7 of the micro, remove IC 104 and see if it turns on the TV pin 7 it must have 5v	By c of 4.7μF instead of ic 104, -pin2 and +pin4	BRUSKE
PHILCO	TPF2121	When turning on it makes a noise on the flyback and it doesn't oscillate	D 908 shorted	Replace d 908 for an original	haecio