Philco Repair Tips

Search: philco
Results: 4838

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP14U56	Does not oscillate (turns on). normal voltages. it is only on standby. When you press power it makes tick tick tick and stays on stand by.	I released pin 3 of the photo coupler and then the TV oscillated (turned on), then turned off. I noticed that the vertical core overheated in 3 seconds. so I killed the charade. la78040n.		Tec vídeo
PHILCO	TP 1410	The TV tries to turn on, the LED goes off, disarms the demagnetizer relay, then the LED starts blinking, it doesn't work.	Resolve or exchange r 931		caio
PHILCO	PCM2051	TV with sound; no image, no brightness	C 801 on the trc board	After the replace, everything shine appeared	ELETRON ICA ROCHA FERNANDO ROCHA
PHILCO	PCM 1444 E OUTRAS	Mirror image	R 718 open		Master
PHILCO	TPF29S4F	Closes image in the corners, cushion or cup effect, does not correct pincushion.	D1702 with oxidized terminal glue.		Bruske
PHILCO	TP14U56	Turns on and after 3 to 5 seconds turns off.	Bad solder in the photo coupler region	I observed that all voltages were normal. and I noticed that it oscillated and when it was about to light up the tube went into protection and the LED kept blinking. That's when I suspected the photo coupler region. As I didn't find any defective components, I decided to re-solder that region and it was ok.	Tec vídeo
PHILCO	PCM2044	TV turns on and off by itself, sometimes it takes a few minutes	R713 open		juci
PHILCO	TP-2054	The device is turned on, the screen turns red with incriminate traces, after a few seconds it goes into stand-by,	Metal film resistor, value 10k, on the kinescope board, referring to the red cannon drainer transistor, replace it, it is ok.		CLÁUDIO RIBEIRO, TECNOSAT ELETRONICA E INFORMÁTICA, JATAÍ-GO.
PHILCO	TPF2130	It turns on but when the relay goes off a brief image appears with the frame closing horizontally, it goes to stand by with the LED flashing.	C701 (horizontal deflection) auterated	Replace the c701 (8.2 nf/1.6kv)	Ricardo Moreno
PHILCO	PCS 2956N	High voltage spikes and turns off	Width defect, replace 8n2 and 4n7 ceramic width capacitors and increase the vertical output transistor decipher (2)		Prado
PHILCO	PC2956	There is no voltage in the secondary of the power supply, it just pulses.	C-921=1k per 1kv of shorted disc, only replace with one of the same value, if not the voltage variation.	It was replaced for one of the same value and it was... ok.	Armando da Eletrônica só Tv.
PHILCO	PCS2952	It keeps beeping, beeping and the LED is blinking.	Q 902.	I started it off and it worked.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TPF 2140	It doesn't turn on and it doesn't work on standby.	C 930 with leak in the power supply primary		levilp
PHILCO	PCM2044 CPH05	Vertical fexado.	R.602	Replace.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	PCS-2956 CP-01-LR01	Power supply does not start and chopper driver smokes on pin 7	C922 short (1.0 nf) I replaced it and the problem was solved.	Note: as the c922 is on the pulse line (130v) the power supply activates and disarms successively.	Tecnogil Eletronica
PHILCO	PT20V56	Vertical beam and then switches off	Ceramic capacitor c614		ELETRONICAAC
PHILCO	TP20V56	Vertical beam and then switches off	Ceramic capacitor c614	Ac electronics
PHILCO	PCS2952	Dark image with little contrast	C 716 short /r706 open		betoteck
PHILCO	TPF 2121	Morta (nem da stand by)	D908 e c914	Obs: mude c914 p/ 1000y/35v	VSE Eletrônica(Ádrian)
PHILCO	TP2054	Does not turn on, LED is off.	R 911 amended.	Replace.	This email address is being protected from spambots. You need JavaScript enabled to view it.