Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TP-2054
|
The device is turned on, the screen turns red with incriminate traces, after a few seconds it goes into stand-by, | Metal film resistor, value 10k, on the kinescope board, referring to the red cannon drainer transistor, replace it, it is ok. | CLÁUDIO RIBEIRO, TECNOSAT ELETRONICA E INFORMÁTICA, JATAÍ-GO. | |
| PHILCO |
TPF2130
|
It turns on but when the relay goes off a brief image appears with the frame closing horizontally, it goes to stand by with the LED flashing. | C701 (horizontal deflection) auterated | Replace the c701 (8.2 nf/1.6kv) | Ricardo Moreno |
| PHILCO |
PCS 2956N
|
High voltage spikes and turns off | Width defect, replace 8n2 and 4n7 ceramic width capacitors and increase the vertical output transistor decipher (2) | Prado | |
| PHILCO |
PC2956
|
There is no voltage in the secondary of the power supply, it just pulses. | C-921=1k per 1kv of shorted disc, only replace with one of the same value, if not the voltage variation. | It was replaced for one of the same value and it was... ok. | Armando da Eletrônica só Tv. |
| PHILCO |
PCS2952
|
It keeps beeping, beeping and the LED is blinking. | Q 902. | I started it off and it worked. | |
| PHILCO |
TPF 2140
|
It doesn't turn on and it doesn't work on standby. | C 930 with leak in the power supply primary | levilp | |
| PHILCO |
PCM2044
CPH05 |
Vertical fexado. | R.602 | Replace. | |
| PHILCO |
PCS-2956
CP-01-LR01 |
Power supply does not start and chopper driver smokes on pin 7 | C922 short (1.0 nf) I replaced it and the problem was solved. | Note: as the c922 is on the pulse line (130v) the power supply activates and disarms successively. | Tecnogil Eletronica |
| PHILCO |
PT20V56
|
Vertical beam and then switches off | Ceramic capacitor c614 | ELETRONICAAC | |
| PHILCO |
TP20V56
|
Vertical beam and then switches off | Ceramic capacitor c614 | Ac electronics | |
| PHILCO |
PCS2952
|
Dark image with little contrast | C 716 short /r706 open | betoteck | |
| PHILCO |
TPF 2121
|
Morta (nem da stand by) | D908 e c914 | Obs: mude c914 p/ 1000y/35v | VSE Eletrônica(Ádrian) |
| PHILCO |
TP2054
|
Does not turn on, LED is off. | R 911 amended. | Replace. | |
| PHILCO |
PCM2044
|
Lack of sync and drizzle | C205 - agc and c702 sync. I changed the caps. It started working normally again. |
The two electro/capacitors with high esr. | vxm |
| PHILCO |
TP1452N
|
Does not turn on, stays on standby | When the TV is on stand by with the LED on, replace the zd923 4.7 volt diode and the zd922 3.9 volt diode. | Edilson Ribeiro | |
| PHILCO |
TPF 2941
|
Does not turn on or the LED lights up | All voltages are normal, and the TV does not turn on; fed up with stress, I decided to change [x1] that little crystal that is next to every micro, in this case x1 = 20,250, I changed it, I confirmed, it was the one, [if] it happens, here's the tip | fabinho@3a | |
| PHILCO |
PCR1449
CPH06M |
C912 with leak, change, note there is no general voltage in the secondary | ars | ||
| PHILCO |
PCM-2044
|
When the TV was turned on, it worked with a lot of flickering on the screen and it was difficult to maintain the tuning of a channel and when changing channels it got even worse, it shook the whole screen and was like a simonism of vertical and horizontal | The capacitor c710 with cold soldering, I resoldered it and it was file | It is located next to the dryve of the horizontal | |
| TV PHILCO |
TP 29C21
|
TV doesn't work, STD-BY light stays on | Solution replaced the d-916 smd | jaironuness | |
| PHILCO |
PCM 2044
|
When turning on the image comes back to normal after a while the screen becomes clear until the image disappears | Replace ci tda 8361 s7 |