Philips Repair Tips

Search: philips
Results: 14210

Make	Model	Symptom	Problem	Solution	By
PHILIPS	20PT120A	Doesn't start. When you activate the control, the LED flashes a few times and comes back on. all normal voltages.	Capacitor 2442 (smd) with cracked or damaged solder.		ECJ
PHILIPS	20PT524 L9.2A	Replace of the same	Q7400 bf 422 short base emitter	Replace of the same	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	15PT136A/00 ANUBIS A	Dark screen with sound	R 3296 (100Ω.) c.i. power supply tda 3504		Grobio
PHILIPS	21PT5432/78 PT	When it is on, it loses tune and comes back at the same moment and sometimes when it comes back on the image some characters appear as if it were resetting the memory.	Internally, the kinescope socket will spark, causing the computer to give a momentary breakdown.	Changing the kinescope socket is the same one used in Panasonic Philips tube devices	Helio Eletrosonic
PHILIPS	21PT5433	With characters but without image with sound	100k open resistor close to the flyback, r-3442		joelton
PHILIPS	20PT3331	TV with primary power supply chirping ticking......ticking.....ticking, and it didn't stabilize the voltage kept oscillating and wouldn't turn on	The integrated one that is below the board in the primary power supply, the tea 1506 t, was replaced	With the replace, the TV was clean and started working normally again, as a precaution, replace the capacitors and resolder the chassis ok thanks	HELIOMAR
PHILIPS	29PT4641/78	It makes it turn on but it doesn't turn on and when it turns on, colored lines appear at the bottom of the screen	C2484 de 10uf 100v e d6457 smd em curto no vertical	Replace	EletroClaudio Aguas Belas
PHILIPS	14PT3131	Cold turns on turns off several times warms up stays normal	Power supply coupler photo.		je_eletronica
PHILIPS	21PT9467C/78	Horizontal transistor was shorted. I put another one. When I turned on the flay back it kept beeping	I changed the flay back; and just run to the hug		DIEGO LIMA
PHILIPS	20PT4331	Keeps turning on and off with the vertical closed	Replacing the 3448/9448 resistor on the 180v line		VALDEMIR - NV ELETRONICA
PHILIPS	21PT9467	This TV arrived at my workshop with a burnt vertical ci, I replaced it but a resistor at the base of the ci was hot and with thin stripes on the TV screen	The vertical one was not the original	Putting the original vertical was normal, just run for the hug.	ozenildo
PHILIPS	29GX1899/78R	Stretched image/pulling to one color/taking time for the image to appear	Cap.elet.position 2431 (100mf x 200v) completely exhausted.	Replace the same.	jheliocavalcanti
PHILIPS	20PT529A	Turns off after a few minutes on	Cold solder on flyback negative	Re-weld the flyback	Filipe
PHILIPS	14PT3331	It turned on but after 1 second it turned off it generated but stopped standby it came on	Smd capacitor 2518 position on the board	Thanks to the friend who gave this tip, he just replaced it and the TV worked normally, thank you	janilson
PHILIPS	29PT4643 LO4U-AA	Replace note; if the horizontal output burns out after replacing it, replace the flyback	7408 with changed	Replace note; if the horizontal output burns out after replacing it, replace the flyback	paulo-maceio/al
PHILIPS	29PT554	Does not turn on, the LED does not light up, there is no voltage +b	33 k 3510 resistor close to the rectifier	Barter it	FELIPE
PHILIPS	TV 29PT4635	It has all the +b and it doesn't work	C2455 47x25 weak	Just replace the c2455 for a new one	Paulo Sertel Itararé SP
PHILIPS	21PT9467	TV with a black band at the bottom of +/- a 4 fingers after fly back leaked high voltage	Integrated (ic-102) tda-9372 - does it all	Replacing the ic does it all	Nova Eletronica
PHILIPS	29PT4635/78	Vertical closed	3488 resistor near 4.7lr charred flyback	Replacement	Eliel
PHILIPS	FW-C252 FW-C252	Turns on normally - but doesn't open the CD cover - and there's no sound - not even on the radio	Where there should be 12v there is 5v cause---diode - 6394 - 1n4003	Diodo - 6394 - 1n4003	neupsx4download