Philips Repair Tips

Search: philips
Results: 14206

Make	Model	Symptom	Problem	Solution	By
PHILIPS	32PHG4900	I'm sound	Bios memory - u406; rewrite or change		Thiago MC Jaú
PHILIPS	HTS3510/78	Locked with the Philips logo on the display	Reset memory	Jump pin 3 of the XP15 connector to pin 13 of the XP9 connector, connect and then remove the jumper	Driu
PHILIPS	40PFL5606D/78	Duplicated and inverted image.	Rusty v-con and t-con flats.	Cleaning of flat contacts and image returned to normal.	TECNOBRU SBC
PHILIPS	FWM208	Improve the serious	Put 10n cap in parallel with c539 and c540		Warley cesar
PHILIPS	FWM208	Doesn't start	Smd cap 104nf parallel with the r bridge	Replace components. install the bridge outside the board with heatsink, heatsink on the q501, place 2 103 caps, one in parallel with r540 and the other with r543, making the woofer with bass and mid-bass. it turned out great.	Warley cesar
PHILIPS	FWM377	Is only on standby	Loose drawer loading rubber. The device has to read the drawer sensors to release the on function		Ulisses Bernardes
PHILIPS	42PFL3604/78	Doesn't turn on/sometimes turns on	Replace capacitors smd-c114/c80/c111/c417/c109/c113/c110/c474/c112/c155/c99/c168, note: some of them are inside the shielding plate of the microprocessor, after the change, wash the processor ci and the memory ci with brush and thinner		reginaldo moronte,eletronica junior caldas novas
PHILIPS	32PFL3018D	After changing the memory, the primary colors on the screen alternate.	Burn adjustment	With the TV on, type on the remote: menu, 1999, return. locate "burn in" and switch to off.	Persio (TVCompany)
PHILIPS	47PFL3007D/ 78	After being on for three hours, tsound is a strong hissing sound when we talk and it turns off and back on, sometimes the line on the screen	U701 regulator 3.3v altered p/4.27v	And just replace and run for the hug	JOSE HUMBERTO F SANTOS
PHILIPS	48PFG6110/78 TPM 15.3L_LA	The tip is that the 55pfg5100/78 the scheme is the same as both the power supply and the main	Download the file from this site and good luck.		GDP2
PHILIPS	NX5	Turning off right after turning on	DC current protection circuit at output	This circuit is simply not included in the schematic, but it is mainly composed of 2 transistors and 2 SMD resistors, what causes the problem are usually the 68k resistors, very close to one of the output inductors.	davi.sls
PHILIPS	39PFL3008D/78	Doesn't start	It only turned on the LED without an image, the back light flashed	Remove the memory, turn it on without the memory, then turn it off and solder the memory in place, it almost always works 100%
TV PHILIPS	42PFL6007	TV doesn't turn on, just red light	Voltage did not double, change q603 q581.stk160		luiz mario rocha
PHILIPS	HTS3011	It doesn't even turn on at +5v..12..2?...etc.	Raqqaa Saqaa	I went to the crowd	Alextecnico
PHILIPS	32PFL4007	Turns on, everything is normal, after a few seconds it turns off and restarts. turns on, Philips, turns off and stays like that the whole time.	Monitor the voltage on the 3.3v regulator u701. It has to be 3.3 volts. in my case tsound was 3.9v.	Replace u701, 3.3v regulator.	arock
PHILIPS	AZ1575	Power button bad contact	Repair button		César zeppelini
PHILIPS	43PFG5000	Turns on, "Philips" logo appears, turns off. The process is repeated all the time.	Try firmware update without success. The TV does not recognize a pen driver, with software for updating. continues: turn on, logo, turn off.	Resolved by changing the eprom memory	arock
PHILIPS	40PFL3606D	Black lite black screen lights up	Resistor with open	Replace resistor 750k position 7503	JORGETVPARANÁ
PHILIPS	21PT9467C/78	League without sound and image, with characters	D302 1n4148 with leak, you have to remove it to measure	To replace. tip sound from the channel	GDP2 Macajuba-ba
PHILIPS	14GL1016/78	Turns on with sound, and without image.	Bad flyback, just change it, it will return to normal.		Marcones de Araripina-PE