Philips Repair Tips

Search: philips
Results: 14243

Make	Model	Symptom	Problem	Solution	By
PHILIPS	26PF5321	TV only turned on after several attempts and warming up.	Capacitor c130 - 100uf x 25v on the device's power supply board.	I replaced the c130 capacitor with the same capacitance. As I didn't have a 25v capacitor on my bench, I placed one with a higher voltage limit: 50v. This modification is not problematic, you just have to respect the minimum limit and place it equal or higher.	Villeneve Oliveira
PHILIPS	32PFL5403 LC8.1L LA	Doesn't start	Absence of 3.3v	Changing the r929, 1r resistor that works as a fuse, if not, I replaced it with 1r1	Zener Serviço Técnico
PHILIPS	AZ1133	Sound on normal CD, am and fm with very low sound, you can only hear it if you put your ear to the speaker	1000p smd capacitor, position c82 (has lap on it).	Replace capacitor smd c82.	J&M
PHILIPS	32PFL3404 TCM3.1L	It turns off in a few minutes, sometimes tsound is a beep from the speaker, it does not obey commands from the remote control or the TV.	Lack of grounding in the housing of the x5 crystal (16mhz) close to u8. definitive solution	Take a piece of bare jamper, go around the crystal and solder it to the housing and to a ground point. Obstodo topics previously sent are correlated to this defect.	cici.muniz
PHILIPS	40PFG5000	Lowering the current of the LEDs so they don't burn	Retire os resistores smd r8614 r8615 r8616		reginaldo moronte,eletronica junior caldas novas
PHILIPS	32PFL3707	All total dead stop	Power supply	Replace d9104,q9107,d9107/zd9106 and r;9159 because tsound was a power outage burning these components, just replace them in my case, ok, luck to everyone, aai	eletronica publison natal rgn
PHILIPS	50PFG4109	Reducing the current of the LEDs to avoid burning	Remove the smd resistors from the board r8148,r8149,r8144		reginaldo moronte,eletronica junior caldas novas
PHILIPS	42PFL5007G/78	Em stend bey	Poor contact on the t501 transformer on the primary power supply.	Remove the welds and redo them all regarding the t501	MULTIMARCAS/ACARI
PHILIPS	40PFL5606D/78	Completely stopped, 3.3v present...	Short on the 12 volt line... I found shorted 10mfd smd capacitors, they are connected to pin 2 of the ci 7125. check surrounding components. good luck...		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	32PHG5813	No image with sound	LED bar make the change and change the five current resistors until you get 1.2r	Replace the LED and replace the value of the resistors and that's it	orlando lott
PHILIPS	FWM 417X/78 HC01109084974	Locked, does not come out of standby	Condultor na pci do cd l554 aberto	Replace	JOÃOELETRONICO
PHILIPS	42PFL5007G	Changing +12v supply voltages, turning off when starting	Faulty photocoupler	Replace pc501, el817	HAHNRAHN
PHILIPS	20PT3331/78	Turns on with the screen off low power supply	Fotoacloplado	Photocoupled replace	Cícero ajude pra se ajudado
PHILIPS	32PFL4017G	Negative image	Lvds cable at the tcom input with zinabre, cleaning was carried out, the tv returned to normal		jorge
PHILIPS	42PFG6809/78	Backlight off	Checked pfc inoperative, it is part of the circuit that powers the backlight power supply	Remove and clean glue from r 9801, 9802 and 9803.	Ricardo RR
PHILIPS	42PFL3507D/78	Inoperative standybay off	Replace the power supply part capacitor position c9353 replace with a 470mf 16v		C.M eletronica
PHILIPS	46PFL3008D/78	It just stays on standby,	U702	Replace u702 1.8v regulator	Gabriel GXP
PHILIPS	40PFL3606D	Back light off, with sound and background image	Only the back light circuit stopped (inverting)	Measure all 22r resistors on the inverter, in my case the open resistors r438, r456 and r453	Alex Lopes <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
PHILIPS	40PFL5605	Doesn't start	Change diode d907,911 I put sb5200		cleber lima rs
PHILIPS	55PUG6801/78	Does not turn on, completely inoperative, without +12v	Change without testing d9104 and u9109, remember that it works with a separate resistive bridge, it will show everything correctly, but it does not oscillate for feedback, take advantage and change all the electrolytics in the power supply!		HAHNRAHN