Philips Repair Tips

Search: philips
Results: 14206

Make	Model	Symptom	Problem	Solution	By
PHILIPS	FWM3500/55 2013	No sound turning on normally	L605	Replace micro inductor 12.	PU9GTA
PHILIPS	FWM6500/55	Does not turn on, does not come out of stand by (stand by LED on)	L544 on the CD board		Janilson JD ELETRONICA CAETITÉ-BA
PHILIPS	42PFL3507	So acende stdby	When you turn on the signal board, the 5v at the power supply drops to 2.7	9353 power supply capacitor replace without testing	alexandre
PHILIPS	NTRX500X/78	Didn't care	Shorted power supply diode d8	Just replace diode	Valerio
PHILIPS	21PT5433/78	Vertical from the middle up closed and device turning off.	Smd diode position: d6460 bas316, as I didn't have it I used the 1n4007 and that's it. TV working perfectly without conflicts.		EletroGarske
PHILIPS	21PT5433/78	When it starts up, a blurry screen with blurry colors appears, very weak and without brightness. lasts 4 to 7 seconds and goes into cut	Bc546 board position:7463		EletroGarske
PHILIPS	40PFL4007G	Turns on and doesn't leave the Philips logo	Regulator u701 or u415 3v3	If the voltage is higher or lower and just replace	ELENILSON
PHILIPS	42PFL4007G	When turning on, the TV hangs on the blue screen saying "HDMI". It doesn't respond to any commands on the TV's remote control or keyboard and it doesn't turn off.	Firmware (pkg) corrupt.	Software update via USB. After the update, the TV will restart and the reset option will appear. click ok and call the customer!	GM Televisores
PHILIPS	20PT222A L7PLUS	Vertical lines from top to bottom shaking	R3408, 220r, replace.		Joaomvjr
PHILIPS	29PT4635/78	Image closed on the sides (03 fingers on each side)	I had nowsound else to look for this defect, for a few days I checked all the tips from my colleagues and nothing.	I decided to remove the driver that is in position 3430,3431. the image opened, as tsound was no other one to restore it, it remained like that (without the driver). I tested it for a few hours and that's it!	KÁIO/ E.S
PHILIPS	MCM-285	Hoarse and low sound	C319 (100μ x 16v) com fuga.	Just replace. Note: a 220μ x 16v can be placed and it will be fine. good luck friends.	Giovani
PHILIPS	FWM650	I'm sound	642 in the power supply of q611 that outputs 12v, which feeds the q607 in ci q601 on pin 1 has 8v	Cap 642 220μF that feeds base.	GUINGA sdia - goias
PHILIPS	NTRX-505/78	It turns on, but tsound is no sound and it works partially, with the mixer setting in the middle, it keeps hitting the speaker, in fact the operation is incomplete, some LEDs for functions "a and b", type usb "a"/aux/tuner/etc , do not light	All normal power supplys at the bottom, but on the main panel, the top of the device on the main board has a 47uf/10v position cap c521 that its "esr" is changed, only with an esr reader capacitance to find out, then in Doubt change this capacitor. the c521 is located next to the ic "u501 on its pin 38	Swap c521 electrolytic 47μF/10v	MIGUELTV
PHILIPS	14PT6107E/00 TDVD1.1E	Does not start, LED blinks	Check cp12 and rp06		jose almeida tavares
PHILIPS	21PT6456/78	Turns on with red lines top with luminous stripe bottom closed and off	Resistor 3448	Replace is over	Eletrônica ramos
PHILIPS	21PT6456/78	Does not open vertically with red lines turns off r3470	Change without measuring		Eletrônica ramos
PHILIPS	21PT6456/78	Vertically closed at the top about 5 centimeters and turn off	Replace open resistor r3446	Replace is over	Eletrônica ramos
PHILIPS	FWM210	No audio and making crackles in the pre signal	Mosfet q502 buk7535 e ic501 tda7498l		Muniz eletrônica
PHILIPS	32PFL3404	Pisca led 3x	Q3, behind the plate.	Replace	Joaomvjr
PHILIPS	32PFL5604/78	TV turns on, suddenly beeps loudly, freezes the image and restarts	Ripple in tertiary feeding	Electrolytic c474 on the main board with altered capacitance. don't test! to replace	vapcomputadores