☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14231
Make Model Symptom Problem Solution By
PHILIPS 9467/S
Tsound is a hiss or noise in the sound in (vhf) in normal audio, as the volume increases the noise also increases The problem is located on the (fm) board wsound the ic 801 is located. In my case, I just resoldered the board and the problem was solved. Ademar Videira SC
PHILIPS 32PFL3605D
Turns on and off LED flashes two and four times Shorted speakers Replace paulo-maceio/al
PHILIPS 40PFL5605
It doesn't turn on or stay on standby. Falta de z,zv on plaça da power supply. Diode d911 shorted. (it is in parallel with d907) Persio(TVCompany)
PHILIPS 40PFL5605 40PFL6605
Inoperative. doesn't connect at all. no stand by led Shorted diode d911 Really replace and go for the hug Deusomar
PHILIPS 14GX1515
Doesn't start Power supply plate capacitor 4.7x25v 47x25v Capacitor ELETRONICA MAURI JUNIOR
PHILIPS FWM371
Standby LED comes on but does not turn on R39 of 4r7 roasted Just replace paial.eletros
PHILIPS 20PT122A/78
L7L 		Without video, without osd, with sound Sande castle no pino 38 do tda 8362 com 4v. Replace d6461, in4148 with leak jasvan souza
PHILIPS 14PT3336
Doesn't work, doesn't light up or stand-by C.i power supply oscillator str-w6765 Eletronica Lelo
PHILIPS 21PT5433/78R
It called with normal audio but a hundred images. I wasted a lot of time with several attempts. and nothing. R 3442 of 100k open raul de saja
PHILIPS 29PT8457
.... 		TV works normally but with a high pitched noise Non-horizontal coil l 5401 Replace E matos
PHILIPS 20PT326
LED lights up, comes on high, then turns off R3630 (47k) aberto cabessaonatal
PHILIPS 21PT5435
Nothing turns on, not even the stand bay LED. Photo coupler Changing the photo coupler Eletronica Valenca
PHILIPS 42PFL3604
LED blinking weakly did not turn on I replaced c806, they say it has to be original (4.7x450v) for a 10x450v one, no problems
PHILIPS 40PFL5615D/78
Does not turn on, does not light up standby LED, no power supply on the secondary circuit of the power supply board Check diodes d907 and d911, both sb260, which are in parallel. One or both may be shorted. replace both, even if one of them measures good. replace with the same value sb260. mbr360 also goes in place. Diego Korvo Ponta Grossa
PHILIPS 32PFL3403
Image disappears, backlight on, display voltage low, less than 10v. correct voltage is 12v. Replace 5v6 zener diode position 6r02, on the 7r10 regulator transistor side. back side of the main board. joaomvjr
PHILIPS 20PT3331/78
Does not turn on or the LED lights up Killing the 3.3v Check pins 54,56 and 61 measuring on the diode scale black tip on ground and red on related pins reports short replace microna tda9370ps/n2/ai toninho da eletronica
PHILIPS 26PFL3404
TPS2.1E LA 		It doesn't turn on anything, it doesn't even have 5v on standby Ic 901 (tny274pn) Baguatech
PHILIPS 29PT554A
Dark horizontal lines across the screen. 3411 open resistor Nedson
PHILIPS 21GX1665
Jagged and shaking image The 2 47/160v capacitors And just replace and plz EDSON SAO LOURENCO MG
PHILIPS 32PFL3404
Does not turn on, stand by on, no 24v power supply Doubler circuit with low voltage in c3 and c4 12v relay, k1 defective VipCenter