Search: philips
Results: 14231
Make Model Symptom Problem Solution By
PHILIPS 20PF4121
LC4.1E AB
With sound, without image Capacitor ce06 and ce07 both 1000µF on the power supply board (PSU). sim tv
PHILIPS 42PF9631
BJ3.0E
Without sound and image. turns on and flashes for 1 or 2 seconds, relay turns on and off LED remains green Check crystal 27mhz sim tv
PHILIPS FWC270
19
No sound good output, slight hiss Transistor smd 7606 Remove and test the sound should come out without it matrix10y
PHILIPS 40PFL6606D
S L11M1.1L LA
Doesn't even turn on the LED Keyboard I removed the cable from the board and it started working again, I cleaned it with isopropyl alcohol and it resolved Eletrônica Ômega
PHILIPS 42PFG6519/78
Stuck on logo and inverted image Replace a pci principal Type 062598 + menu (box) + screen code (back cover) if it turns on with inverted image type menu (box) + 1999 + return on the control, replace the flip panel option to off or vice versa. Marcelo-Birigui/Sp Eletronica Audio e Video
PHILIPS FWM3500/55
2013
No sound turning on normally L605 Replace micro inductor 12. PU9GTA
PHILIPS FWM6500/55
Does not turn on, does not come out of stand by (stand by LED on) L544 on the CD board Janilson JD ELETRONICA CAETITÉ-BA
PHILIPS 42PFL3507
So acende stdby When you turn on the signal board, the 5v at the power supply drops to 2.7 9353 power supply capacitor replace without testing alexandre
PHILIPS NTRX500X/78
Didn't care Shorted power supply diode d8 Just replace diode Valerio
PHILIPS 21PT5433/78
Vertical from the middle up closed and device turning off. Smd diode position: d6460 bas316, as I didn't have it I used the 1n4007 and that's it. TV working perfectly without conflicts. EletroGarske
PHILIPS 21PT5433/78
When it starts up, a blurry screen with blurry colors appears, very weak and without brightness. lasts 4 to 7 seconds and goes into cut Bc546 board position:7463 EletroGarske
PHILIPS 40PFL4007G
Turns on and doesn't leave the Philips logo Regulator u701 or u415 3v3 If the voltage is higher or lower and just replace ELENILSON
PHILIPS 42PFL4007G
When turning on, the TV hangs on the blue screen saying "HDMI". It doesn't respond to any commands on the TV's remote control or keyboard and it doesn't turn off. Firmware (pkg) corrupt. Software update via USB. After the update, the TV will restart and the reset option will appear. click ok and call the customer! GM Televisores
PHILIPS 20PT222A
L7PLUS
Vertical lines from top to bottom shaking R3408, 220r, replace. Joaomvjr
PHILIPS 29PT4635/78
Image closed on the sides (03 fingers on each side) I had nowsound else to look for this defect, for a few days I checked all the tips from my colleagues and nothing. I decided to remove the driver that is in position 3430,3431. the image opened, as tsound was no other one to restore it, it remained like that (without the driver). I tested it for a few hours and that's it! KÁIO/ E.S
PHILIPS MCM-285
Hoarse and low sound C319 (100μ x 16v) com fuga. Just replace. Note: a 220μ x 16v can be placed and it will be fine. good luck friends. Giovani
PHILIPS FWM650
I'm sound 642 in the power supply of q611 that outputs 12v, which feeds the q607 in ci q601 on pin 1 has 8v Cap 642 220μF that feeds base. GUINGA sdia - goias
PHILIPS NTRX-505/78
It turns on, but tsound is no sound and it works partially, with the mixer setting in the middle, it keeps hitting the speaker, in fact the operation is incomplete, some LEDs for functions "a and b", type usb "a"/aux/tuner/etc , do not light All normal power supplys at the bottom, but on the main panel, the top of the device on the main board has a 47uf/10v position cap c521 that its "esr" is changed, only with an esr reader capacitance to find out, then in Doubt change this capacitor. the c521 is located next to the ic "u501 on its pin 38 Swap c521 electrolytic 47μF/10v MIGUELTV
PHILIPS 14PT6107E/00
TDVD1.1E
Does not start, LED blinks Check cp12 and rp06 jose almeida tavares
PHILIPS 21PT6456/78
Turns on with red lines top with luminous stripe bottom closed and off Resistor 3448 Replace is over Eletrônica ramos