Philips Repair Tips
Search: philips
Results: 14206
Results: 14206
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
AZ 1101/01
|
Only the CD and tape were working, the radio was muted. | Cold solder the power supply components near the headphone jack. | Marcio Magalhães Eletronica | |
| PHILIPS |
29PT4635
|
Burning horizontal outlet | Diode,6460 pickle | jps, eletr,c,grande | |
| PHILIPS |
21PT9467C/78
|
Totally inoperative. LED doesn't even light + b with 169vts. other secondary voltages do not exist. | D610 shorted | TonicoBH | |
| PHILIPS |
29PT4631
|
It has all voltages, it oscillates, everything is ok but it does not generate any voltage on the fly back | Bu 4508 short only the base with the emitter | Replace the bu and check the 1,600 v capacitor | kin |
| PHILIPS |
14PT218A/78R
|
Takes time to turn on or works intermittently | Capacitor 2411 (47mf/25v) with capacitance loss | Replace c2411 with 47mf/50v | samuel leite |
| PHILIPS |
29GX1895
|
Tsound is only audio with the volume at maximum | Volume controller board | Volume controller board (it is next to the microprocessor) | LUIS CARLOS |
| PHILIPS |
20PT3331
|
It turns on normally after approximately 30 seconds, closes the panel and turns off, sometimes it takes a little longer. | Photocoupler | Replace directly and if the capacitors are studied, replace them too and then just run for the hug. | Danieleletronica |
| PHILIPS |
42PFL3403
|
No image with sound | C236 (2200x25),c235 (2200x25) swollen and broken solder on the inverter pins | Replace and store gravel | eletronicaeltec |
| PHILIPS |
21PT6456
|
Turns on and then turns off, if you leave it on, it stays on | Zener +33 volts | Changing the zener, even when measuring correctly, for some reason causes an overload on the +160 volt line | deuner |
| PHILIPS |
29PT552A/78R
|
Baypss LED won't turn on flashing | Capacitor 2575 100n that goes to ground in the optical coupler in short | Replace the same ok | osmar |
| PHILIPS |
14PT 3131/78
|
Does not turn on or the LED lights up | C - 2564 (47uf/160v) | Replace the same | BARRETO CRUZ |
| PHILIPS |
20PT4331
|
Reduced image at the top and no sound. | Replace do c-7465 (10mf/160v) do vertical e c-2444 (470/16v) do audio. | halbert_tec | |
| PHILIPS |
20PT3336/78
|
Vertical; when turned on, a colored rgb band appears at the top of the screen, the screen lights up with a black band at the top and turns off. | Polyester capacitor 2460=104 250v next flyback it changes and lowers 22v supply | Replace for new | beto2828 |
| PHILIPS |
21PT9467C/78
|
It takes time for sound to come out. normal image. | C629 2200ufx16v close to the power supply transformer. | cecé eletronica | |
| PHILIPS |
14PT212A
|
The TV only has standby on when it turns on with control, the stand bay turns off and turns on again | Ci tda9302h vertical | Replacement | samuel abrantes |
| PHILIPS |
20PT3331
78R |
With normal audio dark screen | C 2444 - 470/16v | Replace | Mauro Mascarenha Parazinho - Ce |
| PHILIPS |
20PT3331
78R |
Dark screen with normal audio | C 2444 - 470/16v | Replace | Mauro Mascarenha Parazinho - Ce |
| PHILIPS |
20PT3331
78R |
Dead | R3445 resistor fusivel | Replace | Mauro Mascarenha Parazinho - Ce |
| PHILIPS |
20PT3331
78R |
Dark screen with audio | C 2444 - 470/16v | Replace | Mauro Mascarenha Parazinho - Ce |
| PHILIPS |
29PT5645
|
Turns on, RGB stripes appear in the middle of the screen, then an image with retrace lines appears at the top. | C2465(10uf x 100v) with low capacitance and cold soldering on some uoc pins. | Replace c2465 e resolder or uoc ci 7200 smd. | Rondinele Campo Redondo/RN |