Philips Repair Tips
Search: philips
Results: 14231
Results: 14231
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
20 MT 21 31/78
|
It doesn't turn on and the stand-by LED is stuck, it oscillates when you press power on the remote control. | ,I checked the good condition of the soldering on the pins of the large integrated ci- 7200,even though it was in good condition, I carried out a careful re-soldering,this device is so difficult to maintain,it started to work perfectly, ok !!!!!!-- | ELIZEU RAMOS | |
| PHILIPS |
MONITOR 150S6FS
|
Functions frozen, dark screen | Unlock by pressing and holding the ok key, after message enter my color change until image appears | warley cesar | |
| PHILIPS |
20GL1344
|
Does not turn on, all primary voltages are low. | Audio amplifier. | FERNANDO S | |
| PHILIPS |
42PFL5332
LC7.1A.LA |
The device has a blue LED on, as if it were on, without an image, it does not respond to commands | Right and left inverter capacitors swollen 470mf/35v mosfet burnt fdd8447l | I replaced the capacitors and mosfet and it was ok, don't replace boards without trying to fix them, your profit will be higher | Ricardo |
| PHILIPS |
21PT9467
|
AV input no image only audio | Dz454 shorted | paial.eletros | |
| PHILIPS |
21PT9467
SK4.0L |
Dark image (with osd) | D307 (1n4148) near the flyback on the bcr line (abl) | Baguatech | |
| PHILIPS |
20PT3331
|
Image with white spots on the side of the characters | C2207 100n with broken terminal on pin 37 of the micro | Replacelo | antonio nobrega(patos pb) |
| PHILIPS |
29GX1899
GR6 |
Alloy appears in the image and after a few minutes it returns to normal | Damaged pipe socket | Replace the same | |
| PHILIPS |
29GX1899
|
Alloy appears in the image and after a few minutes it returns to normal | Trc tube socket replacement | ||
| PHILIPS |
14PT1552
L6.1 |
The TV starts up but the screen doesn't light up completely | Leaky 7505 transistor | Replace the transistor | jose almeida tavares |
| PHILIPS |
21PT9467
|
Volume lowers by itself with the fixed bar on the screen until 0 | Ver diode zenner d206 | Master Eletronica | |
| PHILIPS |
29PT4643
LO4U |
Device affected by electrical discharge: normal image but no sound. - note: Audio signal present on pins 01 and 09 of the amp. output. | Causa: q7991(bc847b) e q7992(idem) | Swap them and go for a hug! happiness to everyone. | ADHEMAR CAETANO DA SILVA (TECMIL ELETRONICA) NOVA FRIBURGO, RJ |
| PHILIPS |
29PT4645
LO4U |
Device affected by electrical discharge: normal image but no sound. - note: Audio signal present on pins 01 and 09 of the amp. output. | Causa: q7991(bc847b) e q7992(idem) | Swap them and go for a hug! happiness to everyone. | ADHEMAR CAETANO DA SILVA (TECMIL ELETRONICA) NOVA FRIBURGO, RJ |
| PHILIPS |
20PT123 A
|
LED flashes in sequence and does not start, that is, it does not work. | C-2447=680pfx1kv shorted, close to the horizontal output three, and when this happens the 10k r3454 smokes and you also have to change it. | Solution was replaced c2447=680pf of 1kv and r3454=10k and it was beautiful. | Armando de Olimpia Eletronica EvoluSom |
| PHILIPS |
21PT9467/77
|
Colored vertical lines at the top of the screen | Capacitor 303 1000x25 open diode 302 open d ba158 | odilon | |
| PHILIPS |
FWC505
|
It turned everything on, but it didn't turn on the panel or the CD drawer came out, nor did it move or remove the optical drive. Well, the panel defect, I checked that the panel was missing negative voltage (-23v), I traced it back to the power supply and discovered the 4.7r resistor r3211 was open, I replaced it, it came back, but the mechanism wasn't, I checked all the voltages, everything was ok, but one of the mechanical drivers, which was not the one in the drawer, was getting very hot, I changed it, if I'm not mistaken, a tda 7370, then I changed the other one, driver 7871, the same number, then everything was ok... I hope I helped someone... hugs | R3211 de 4,7r aberto ,driver 7871 | SYSTEM ELETRONICA | |
| PHILIPS |
29PT5642/78
L04U |
Doesn't start. | C2411* (near the horizontal exit) | *check the table in the schematic for other models of the same chassis | Baguatech |
| PHILIPS |
FWC270
|
No sound. and when you unplug it, sound comes out | Remove fet from position 7302 and test the sound to see if audio comes out. | If Audio goes out, put a new fet | Wanderlei Studio - Eletrônica Áudio e Vídeo - Quixadá |
| PHILIPS |
14PT4131
|
Image moved up | Image shifted up, swap transistors 7461 and 7462 | Replaced | Reginaldo WK Eletrônica |
| PHILIPS |
28GR7580
|
No tune - no 33v | Automatic tuning took a long time and didn't find any channel, the 33v was missing | Next to the seletronic, replace open r108. | Trendset |