Sanyo Repair Tips
Search: sanyo
Results: 852
Results: 852
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SANYO |
CBP2876
|
Red, green & blue flyback lines | C700 100µ hi esr | ||
| SANYO |
CBP2872 ED1
|
No sound when sw on if still warm | Ic560 adc2301e on sigs panel pt no 409 211 9404 | ||
| SANYO |
CBP2872 ED1
|
No sound - comes on briefly when cold sometimes with crackle/hiss | Ok from scart socket - ic561 apu2471 could be faulty | ||
| SANYO |
CBP2872 ED1
|
Lines when cold with shading as warms up | C404 (100mfd 50v) in the frame stage was the culprit, although its esr reading was ok, and there were no signs of leakage | ||
| SANYO |
CBP2872
|
Repeat fail of lop tr ( 2sd1555 ) | Ic dpu2553 | ||
| SANYO |
CBP2872
|
No sound from spkrs - ok from scart | Ic561 apu2471 on sigs panel | ||
| SANYO |
CBP2866
|
Int trip/blank raster/no field sync | Ic780 12v reg - use tip41 & 13v zener & 27v dropper as reg nla | ||
| SANYO |
CBP2865 E3A28
|
Picture and sound goes off int. | 12v reg ic780 failed when hot. | ||
| SANYO |
CBP2865 E3
|
Int sound/pic with bright white raster with low height or field collapse reverting to st/by | Ic780 si3122v 12v reg s/c internally when heated | ||
| SANYO |
CBP2865
|
Int bright raster with reduced height | Replace ic780 12v regulator | ||
| SANYO |
CBP2580A EB2 SERIES
|
Tripping - even with psu on dummy load | Black jumper wire which runs from the earth side of the chopper transformer to a point very close to ic351 a regulator ic, was dry jointed at the chopper transformer end. | ||
| SANYO |
CBP2580 EB125
|
This set would shut down interrnittently: the peri | The set could be made to run indefinitely by entering the service mode ( menu on the set's control panel , followed by menu on | ||
| SANYO |
CBP2580 EB1
|
To enter service mode | Menu on set's control panel, followed by menu on r/c handset | ||
| SANYO |
CBP2580 EB1
|
Shuts down int - runs ok in service mode if im bus run is stopped | Fault somewhere on the im bus - nvm3060 eeprom on digiboard cured fault | ||
| SANYO |
CBP2580 EB1
|
Colour lost & pic shifted to right when heated | Xtal x403 pt no 610 217 1037 | ||
| SANYO |
CBP2580 EB1
|
After 2-3 hrs colour goes and picture shifts to r | Xtal x403 drifting pt no 610 217 1037 | ||
| SANYO |
CBP2580
|
St/by only - trips at start up | 22mfd 250v b+ decoupler s/c | ||
| SANYO |
CBP2580
|
Int start up - eht can be heard | Check for int mains switch | ||
| SANYO |
CBP2576A/00
|
Bright blue raster with fb lines | Ic500 which is a tea5101a on the crt base pcb. r534 22Ω was ok. | ||
| SANYO |
CBP2576A ED0 CHASSIS
|
No raster | Tea5101a rgb chip |