Sanyo Repair Tips

Search: sanyo
Results: 852

Make	Model	Symptom	Problem	Solution	By
SANYO	C20 DN4AVN PT92	Does not start, +b voltages and secondary stage ok, no voltages recovered.	Capacitor CP18 (47mf/160v) dry		Filipe Sequeira
SANYO	CTP-6791	This TV was in the av and the screen was dark and it wouldn't come out of the av, the keyboard was stuck and it also wouldn't hold the control, it wouldn't turn on or off only when I took it out and put it in the socket	I changed the micro ic801 lc864512v the TV was ok		eletroclaudio aguas belas pe
SANYO	CTP-3792	TV with the screen narrowing like a square and taking a long time to light up	Burnt deflector		This email address is being protected from spambots. You need JavaScript enabled to view it.
SANYO	CTP 3781-P	Doesn't start	I checked the transistor 2sd1649 for a short. When changing it it worked for a while and then stopped. I disconnected the load from horizontal and still the +b voltage was at 84 v. I changed the 220 x 160v electrolytic and the TV started working again.	Trans replace. 2sd 1649 and electr cap. 220 x 160v (put a 220 x 250v)	ronaldosb
SANYO	C29LH43	No sound and no av coming in	Lack of power in ci 251	Transistor q261 open, just replace it and great	fabiusmax
SANYO	CTP6771	Open lines at the bottom of the screen and the rest of the image is shaking.	Capacitor,c-451=470uf for 16v; low capacity.	It was replaced and it was ok.	Armando da Eletrônica só Tv.
SANYO	C20BG2TXN PT92	Unstable image, when working with /AV input (scart-21 pins)	It broke down after a thunderstorm.	The 1n4148 diode was replaced next to the scart plug, it was passing in both directions.	José Jesus
SANYO	CE28WA4 2116 (SERIE EB5-Z)	When starting the trc it has red return lines then green, finally the video	Socket do trc	Soldar o tr. matte (separate)	joaquim cunha
SANYO	CE28WA4 2116 (SERIE EB5-Z)	Turns on, doesn't start, LED flashes every 4	Ic500(tda6107jf)	Ver fotos de secre	joaquim cunha
SANYO	CTP6792	Power supply inoperative, I tested all the components, and replaced some, everything seemed normal but the power supply did not oscillate	I had the idea of replacing the transistor q613, everything was fine, it measured as if it was good.		fabiusmax
SANYO	CTP-6792 LA3-D	Vertical with retrace lines long, dark image	Replace capacitor c513 1uf 50v	P. resolved	ELTROCLAUDIO
SANYO	C20B62TXN PT11	Dead tv	Resistor r1 5r6 open, with blown fuse after replacing the TV turned on but with a white screen with return lines, tsound was a resistor on the kinescope board open, r201 270r	Replace	geek1966
SANYO	CE-28FN1 EB5-A	Doesn't start,	At power supply r810 (0.33r) open		JOAQUIM CUNHA
SANYO	29PH43B	TV did not generate characters	Vc531	I just made a small adjustment to it and it solved the problem	edilson azevedo
SANYO	CTP3771 A3 D7SB	No sound no image	Replace to transistor on pci q 110 transistor d400		isaias s machado
SANYO	CTP 6791 P	The c 494 (22uf x 250 volts) would heat up and become swollen and the image would turn white with lines of traces	Flyback	I replaced the diode and the ceramic capacitor connected to the c 494 and it didn't solve the problem. replace the flyback and the defect disappeared.	edircap
SANYO	CTP 3722	Totally inoperative	R 410 (6,8 k)	I started checking the power supply, but it was normal, I tested the horizontal oscillator which wasn't working. I then started measuring voltages on the ci 401 pins and came to the conclusion that the defect was at this point, as I found only 4 v instead of 12.7 v on pin 15. I removed the resistor r 410 which was altered. Replaced the resistor and the TV started working normally again.	M&E ELETRONICA
SANYO	C29LH43B	Tune in some channels	33v power supply changed	Replace 39k r505 resistor	marcelo quinelatto
SANYO	CTP3770	Tsh burns without apparent cause.	When you turn on the TV, sometimes the TSH burns out quickly and sometimes it works for a few hours or even days and burns out again, so when you see the board you can notice that in the part of the horizontal drive and in the CI 101 that generates the horizontal signal tsound was a broken solder. , so I redid the solders on both the drive and the ci so the tsh stopped burning immediately but it was still burning due to overheating, I couldn't find the original which was the 2sd1649 so I put the 2sd1650 which didn't hold up, maybe because it wasn't original, then I placed the 2sd1554 which had a very important characteristic that was different from the original, the tf fall time which in the original was 0.4us and in the 2sd1554 was 1us, I then placed the 2sd 1877 which had, in addition to the voltage and current, the same as the The original also had a shorter fall time than the original, and the TV started working normally again.		This email address is being protected from spambots. You need JavaScript enabled to view it.
SANYO	CTP-6781P	Horizontal exit burning	Very high voltage on c361 pos the correct one is 130v	Replace the 100k resistor r350, it must be replaced...	somprimos eletronica