Sharp Repair Tips

Search: sharp
Results: 1785

Make	Model	Symptom	Problem	Solution	By
SHARP	C1417	Screen with an all red image, there was neither green nor blue, output with cold soldering.	Defect in the kinescope plate not working.	It was resoldered and that's it.	Armando de Olimpia Eletronica EvoluSom.
SHARP	C1467B	Doesn't start	Horizontal driver transformer with open winding	After changing it, the TV started working again.	ELETRÔNICA CARLOS
SHARP	C2038	Turning off	Troco do cp 606 7n5 1600v		julio.sertemaq
SHARP	2053	When turned on it turns off quickly	Ic 501 is defective, the 605 causes the TV to turn on, the defect is between pins 4 and 5 of ic 501, activating the protection	Replace ic 501 e ic 104	Paulo tijuca
SHARP	1413 ?	Burning horizontal outlet	Capacitor de bush	Replace bush width capacitor	edson ou tinho
SHARP	20RS02	There is only an image with an almost closed screen. If it enlarges, it becomes blurry and becomes a blue screen.	Disconnect pin 6 of ic202 and open the screen.resolved.		joaquim
SHARP	C-1440	Burning d 732 r2m	R731 33k changed		juci
SHARP	LC 32R24B	It doesn't work, it just flashes power and opc	Remove the power supply, place a 100r resistor on the 5v pin for stand by, 13v must appear	If not, I found a bad photo and a smd transistor q7110 I put a dta143	This email address is being protected from spambots. You need JavaScript enabled to view it.
SHARP	C-1453	Does not turn on normal power supply gives signal of oscillation and immediately goes into protection @@@	C616=6n8x1k6 poliester	Help yourself, leave your tip ass. arni	EETRONICA ARNI-L. LEAL- SC
SHARP	C-14S02	Does not connect all secondary voltages of the power supply without voltage b+ 0 @@@	1.8mega resistor in the primary power supply changed	Help yourself, leave your tip ass. arni	ELETRONICA ARNI-L. LEAL- SC
SHARP	C-29ST54	Vertical closed	D501 open ta8427k short	Replace d501 ta8427k don't put ta8403k doesn't work	ELETRONICA MAURI JUNIOR
SHARP	C2053	Turns on after turns off, sometimes it doesn't turn on	Capacitor 8n2 1k6 com problema	Replace the same	Jat Eletronica rs
SHARP	C1467B		Low sound does not increase		itamar fernandes
SHARP	C-21ST54	Blurred image, brightness and contrast do not work	D611	Replace for 1n4148	SADER
SHARP	C2999	Sem osd	C2014with fault	Remove it, it's back to normal	orlando lott
SHARP	C-2053	It has +b but it doesn't turn on	Q708 and q101 in my case with cold welding	Resolder the mentioned components	PATRICK
SHARP	C2038_C1428	Does not turn on, power supply making noise (tic, tick, tick).	C725 - 47uf/160v		This email address is being protected from spambots. You need JavaScript enabled to view it.
SHARP	C 1453 OU 2053	When turning off the screen, it remains on without an image. Like the screen was washed, that is, it did not turn off completely	Change q706 of the power circuit		pedrinho tela quente
SHARP	20R12	Plug it into the socket, the TV turns on directly if you turn it off using the control or key, it won't turn on anymore, just remove it from the socket and	Photo coupler and the capacitor in the 1000uf 35v power supply	Replace	EletroClaudio Aguas Belas
SHARP	C-20RS03	Does not turn on power supply ok 115v ok 5v ok but does not turn on.	R676 10k aberto	Replace it and run for the hug.	toinho eletron