Sharp Repair Tips

Search: sharp
Results: 1784

Make	Model	Symptom	Problem	Solution	By
SHARP	C1632 OU C1432	High secondary voltage burns 2rm diode	R706 (10r) non-primary, open.	Replace	joaomvjr
SHARP	C2999G	Stop	Replacement of zener diodes d2001 with leakage, d2081 open.	Replace zener diodes d2001,d2081. both 5v6	LIDER ELETRONICA
SHARP	C-20R12	Vertical closed, just a line in the middle of the tube.	Diode d661 shorted and r656 open.	Replace them	toinho eletron
SHARP	C2188	Vertical folding at the bottom	1000mf/35v cap, low capacitance and good esr.	Replace do cap c506 1000mf/35v	LIDER ELETRONICA
SHARP	C1467	Don't care! secondary zero! I don't have the strength to leave	1.8m r704 open	Replacement	orlando lott
SHARP	C-2017	Doesn't start singing like cricket cri, cri, cri etc...	Capacitor c721 ceramic 103k 1kv shorted	Replace it and ok	TONIO DA ELETRONICA
SHARP	C2040B	Very low sound	I changed the output and capacity of one thousand x 25 volts, it didn't help		beto
SHARP	TVC :SHARP C-21 ST 54.	Protection activates 2 seconds after turning on the device	In this case the short was vertical; check the vertical stage, starting with the shorted or leaking diode, ceramic capacitor in parallel with the diode, check 100 mf x 35v filter, resistor r/504,390r/ open	Lastly, changing the vertical output .tda 3653-bq >will solve the problem.	NilsonAraujo
SHARP	C-2040B	Vertical closed just a strip in the middle	Broken r645 and r606 solder c507 exhausted	Resoldering of r645 and r606, changing the c507, which made it work again	fbio
SHARP	C-14T51	When it turns on it makes noise at the power supply	Stk 73907 of poor quality		Eletronica Bianca Ipirá BA
SHARP	C2999	Dark screen with no image. normal sound.	R 882 120k open	Replace res.	DEBIQUE
SHARP	C-29ST58	TV didn't oscillate, all good power supplys, well this TV appeared in the electronics already messed up, in the oscillator circuit I found a toasted resistor r 609=5k6 I changed it and the q602 = tr oscillator and nothing. Then I found it in the vertical output r505=33r toasted and a cap:de100uffor 63v with low capacity and the ic501=tda8350 shorted, I changed it and nda.it was then that in a partnership with my friend stefanio we discovered that it didn't have the 8volts of q754, these 8 volts are what starts the oscillator circuit of the pin 40 of ic200=tda 8375.	Cause in q754 which has 8v it only had 3v, with the help of my friend stefanio we discovered that the cause of everything was the q760=bc858 a smd tr (pnp) that was shorted near the micro.	The q760=bc858 tr smd was replaced, the TV worked and the sμFfering ended uuuuμFa...!	Armando de Olímpia:Eletronica evolusom.
SHARP	C29ST58 0000	Vertical closed top of the screen	R 505 power supply +b 50 v 33r open	I replaced and slept, good luck!	Jhone eletronica
SHARP	C2038 0000	Flashing +b power supply	Cap cer c621 1kx 2kv do hoz c / leak .	Replace without testing......good luck!!	Jhone eletronica
SHARP	C1417	Fountain beeping like flyback	C721 10n	Replace it was shorted	eletronica NDN
SHARP	C 2082	Does not tune channels	R 1008 33k aberto		Amadeu
SHARP	20R12	Goes out of tune, when it goes to tune it doesn't stop automatically on the channel, only manually	T801 coil with changed internal capacitor	Replace to t801e recalibrate it	Paulo Sertel Itararé SP
SHARP	C-2188	Shaking the image.	C-504 = 1uf x 100v. (near the vertical IC heatsink).		FERNANDO S
SHARP	2038 161	Doesn't start	When plugged into the socket, the power supply turns on, voltages are ok and there is a momentary starting pulse, then it does nothing else.	Shorted vertical circuit ic501 (tda8356) after being replaced, it started working again, but colored stripes appeared before the image and after, along with the image, folded stripes on top of the screen, cause of this: r505 (33r broken).	Margutek
SHARP	14S2-BZ	No sound (normal picture without sound)	Rewrite the eeprom		mickey27