Sony Repair Tips
Search: sony
Results: 20088
Results: 20088
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CPD15SF2
|
Control can't correct size, centrg, geom, etc. | Picture size, centering, geometry etc are incorrect. frontpanel control is inoperable or will not correct problem. | ||
| SONY |
CPD15SF2
|
No power up in standby | Unit would not power up in standby mode. | ||
| SONY |
ZSM1
|
Defective fop from stock | Could not adjust laser power on replacement fop. meter wouldfluctuate between both ends of teh scale but could not set powercorrectly. | ||
| SONY |
ZSM1
|
Would not load certain mini disks | Unit would not load certain disks. the mz1 would load thesame disks with no problems. | ||
| SONY |
WMSXF44
|
No radio function | Flex board between main board and tuner board bends and opens. replace with new flex board and problem will occur again. | ||
| SONY |
WMGX90
|
Tape keeps switching direction | Ic701 pin 32 missing 3 volts which turns q401/332 onwhich drive dc-dc and rotation detect. my problem is that ic701 is notlisted in manual and control board is not available in kc. | ||
| SONY |
WMGX300
|
Incorrect part number for motor - correct p/n is x33711691 | Incorrect part number for motor assy for this unit. -hq comments: please refer to correction-1 (p/n 9-959-645-91). in it youwill find the correct part number for the motor assy, which isx-3371-169-1. | ||
| SONY |
WMFS495
|
No tape function | Unit came in with no tape function. -solution :found belt off. replaced, ok, new belts seem too loose. | ||
| SONY |
WMDDT1
|
No audio | Unit had no audio. found output from ic401 pin 11 lookedmuddy, while charging ic401 i found c409/r409,c405 missing. | ||
| SONY |
WMDD9
|
Unit not shutting off - replace cam gear (ref 368) | Unit not shutting off. tape spindles keep running. when changing sides unit grinds. | ||
| SONY |
WMD6C
|
No audio - c235 torn off board with traces on new version | C235 and traces missing from unit on new version main boards, this is a common occurrance, usually just the cap is loose from solderlands. symptom no audio in one channel. | ||
| SONY |
TCDD7
|
No audio | Unit would play tape but no audio. | ||
| SONY |
MZR2
|
Won't play/record m-o disc (found m-o temp data re-set to 0) | The unit would not play or record m-o discs. have found thatabout 8% of the repairs to this model were for this problem. | ||
| SONY |
MZR2
|
Unusual characters in display | Unit had unusudal characters in display. (s 02e898) | ||
| SONY |
MZ1
|
Recorded audio is distorted in left channel | Records distorted audio in left channel only when using lineinput jack. mic and digital in recorded fine. sent a 1k tone into linein and looked at good waveform at pin 15 of ic303 and a bad waveform atpin 16. | ||
| SONY |
MZ1
|
Part numbers for s706 and s707 | S706 pac in switch and s707 pac click switches were damagedand cannot find my part number for these. they are on flex cable 108. | ||
| SONY |
KCFC25
|
No clock memory back up | No clock back up with the new 9 volts battery. -solution : found 9 volt battery connector was soldered in wrongpolarity. | ||
| SONY |
IPS760
|
Rom part number | Need part number for detect version rom. non are in thecomputer system. old version in manual ic406 is x33671491 and it doesnot update to new part number. -hq comments: contact kansas city parts attn jamie lyon phone816-891-7550 ext 256, fax 816-891- | ||
| SONY |
ICFSW7600G
|
No audio - replace q510, p/n 8-729-230-49 | No audio. tuning ok. no b+ to speaker amp ic501. | ||
| SONY |
ICF2002
|
No audio - replace c159, p/n 1-123-661-00 | No audio. 3v b+ line was being pulled down off ic9, the 3vregulator. |