Sony Repair Tips
Search: sony
Results: 20088
Results: 20088
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
D141
|
#s switched for m901/902 in manual | Reference numbers on page 31 of service manual for motorsswitched. m901/902 in break out are switched. | ||
| SONY |
D141
|
Static noise heard in audio out - replace ic601 (875929718) | Static or noise heard in audio out. | ||
| SONY |
CFD8
|
No power cd | The unit has no power cd that is caused by a little crack on the main board. | ||
| SONY |
CFD8
|
Grinding noise - replace optical block | When no cd in unit, sled motor won't move. when cd in unitsled motor is turning continuously. | ||
| SONY |
CFD8
|
Sb aud 0328 | Replaced ic801 per s/b, now cd shuts down after 9 hours ofcontinuous use. optic and cables ok. -hq comments: the s/b was due to a different symptom as you know. thisunit could have an intermittent problem. | ||
| SONY |
CFD8
|
16p harness cnp701 | There is no part no. for the 16p harness that connects theop block, kss213, to main board. diagram can be found in supplement 1 ofthe cfd8 sm. -hq comments: the part number can be found in the cfd9 service manual,ref 51. it is 1-769-789-11. | ||
| SONY |
CFD758
|
Ic704 different | Unit has different ic704 then s/m. unit uses ska9258dinstead of ba6296fp. is it compatible? original symptom was no sledmotor operation. when ba6296fp installed, the spindle motor would run athigh speed. reinstalled original and original symptom | ||
| SONY |
CFD750
|
Popping noise in audio after power up | Any mode, audio would pop every few seconds | ||
| SONY |
CFD616
|
Error code 90 | When ac first plugged in there is no initialization of unit,no power on, and no back light. display does show the words error 90.any ideas what this error code is? -hq comments: this question was faxed to tokyo. as soon as tokyoanswers, we will info | ||
| SONY |
CFD616
|
Mechanical jammmed and misaligned | Mechanical jammed and misaligned. | ||
| SONY |
CFD610
|
Disc would not spincd palyer sled | Discs would not spin and unit would read discs take out, ordiscs would spin and make a thumping or rubbing sound and unit would skipbadly. | ||
| SONY |
CFD606
|
Cd mechanism jammed | Cd mechanism jammed. very common problem with this modeland similar models, cfd616/626. a disk was found in main tray assy ref217, without a disc holder . | ||
| SONY |
CFD600
|
Unit displays no disc - check solder short on c819 | Unit displays no disc when disc inserted. mechanism wil notgo anywhere. | ||
| SONY |
CFD600
|
Mechanical noise when tape is in unit and playing. | Unit produces rubbing or squeak noise when playing a tape. | ||
| SONY |
CFD600
|
Disc jamming | Disc may become trapped in the disc case after improperloading. | ||
| SONY |
CFD600
|
No pickup/int pickup | Optic wires too short and could cause many cd failures inthis unit. boombox team evaluated 5 units that failed during burn test, 3of 5 failed due to white optic wire connector being slightly pulled out. -solution :replace optic wire set with 1 slightly | ||
| SONY |
CFD560
|
Part number for ic703 | The unit has a different type of ic, ic703 - ks9211 andservice manual listed as cxd1167q. there is not part number in sonyreplacement book. need part number for ks9211tel 810-344-4354 fax 810-344-4899 -hq comments: contact knsas city parts, attn jam | ||
| SONY |
CFD560
|
Distorted audio and then shut down of cd | After unit warmed up cd audio would distort and then unitwould eventually shut down. freezing ic white it was distorted wouldclear up the problem and heating ic would cause problem to reoccur. -hq comments: replaced ic701. | ||
| SONY |
CFD560
|
No audio right side - replace c124 (1-126-176-11) | No audio on right side. good audio on left but not audible. | ||
| SONY |
CFD550
|
Intermittent toc or play | Cables from the laser assy to cd main board are intermittentcausing intermittent toc or play. the part numbers for the cables are notin the service manual. i requested a parts research from kcp, theyresponded that the aprt numbers for these cables are |