Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDX4090
|
Pages 39 - 42 missing from service manual | Cdx-4090 srvice manual. four pages are missing: pages 39 -42. | ||
| SONY |
CCDVX3
|
Mech scraping noise or drum won't turn/rpl screws; sb cam387 | Unit has propblem with excessive mechanical noise, ejectswithout tape in it or won't load tape, check to see whether or not thescrew that holds ref 164 loosens out. so far we had 2 units with samecomplaint. w33g4942 s/n1006109 w33g4203 s/n 1006500 | ||
| SONY |
CCDV9
|
Excess brightness and negative image in evf / new boards | Excess brightness and negative image in evf after installedthe new mcb ordered from npc. found resistors r908 r923 values reversed. -solution :reinstalled r908/r923. evf returned to normal. | ||
| SONY |
CCDTRV70
|
No picture in the lcd monitor / insert data into b0 to bb | No picture in lcd monitor. | ||
| SONY |
CCDTRV70
|
No eject/ drum ramps up/ replace x502 off of ic505 | When powering up unit will spin the drum and stop. no other functions work. after resoldering ic505 same problem. isolated problemon servo board vc125, and found x502 not oscillating. | ||
| SONY |
CCDTRV40
|
No picture in the lcd monitor / insert data into b0 to bb | No picture in lcd monitor. | ||
| SONY |
CCDTRV40
|
No eject/ drum ramps up/ replace x502 off of ic505 | When powering up unit will spin the drum and stop. no other functions work. after resoldering ic505 same problem. isolated problemon servo board vc125, and found x502 not oscillating. | ||
| SONY |
CCDTRV30
|
No picture in the lcd monitor / insert data into b0 to bb | No picture in lcd monitor. | ||
| SONY |
CCDTRV30
|
No eject/ drum ramps up/ replace x502 off of ic505 | When powering up unit will spin the drum and stop. no other functions work. after resoldering ic505 same problem. isolated problemon servo board vc125, and found x502 not oscillating. | ||
| SONY |
CCDTRV30
|
He-20 pcb is missing all components / normal on ccd-trv30/40 | Missing components he-20 | ||
| SONY |
CCDTR93
|
No function at all; no evf / resolder cn504 on the vs125 bd | You hear a beep when changing from vtr mode to camera mode,but no function at all and no evf. found bad cn504 on vs125 board. -solution :resolder cn504 on vs125.- hq comments: cn504 is the connector between the dc to dc converter andthe vs bd. no volt | ||
| SONY |
CCDTR93
|
No eject/ drum ramps up/ replace x502 off of ic505 | When powering up unit will spin the drum and stop. no otherfunctions work. after resoldering ic505 same problem. isolated problemon servo board vc125, and found x502 not oscillating. | ||
| SONY |
CCDTR91
|
No e -e camera mode would come on / resolder-reinstall l651 | Camera section would come on, blink, but no pix thru v/f orvideo out. | ||
| SONY |
CCDTR91
|
No eject caution mode / bad loading motor blew ps501 (vs-99) | Unit cannot eject tape and it is in caution mode. vtr/camerais on. | ||
| SONY |
CCDTR83
|
No function at all; no evf / resolder cn504 on the vs125 bd | You hear a beep when changing from vtr mode to camera mode,but no function at all and no evf. found bad cn504 on vs125 board. -solution :resolder cn504 on vs125.- hq comments: cn504 is the connector between the dc to dc converter andthe vs bd. no volt | ||
| SONY |
CCDTR81
|
In vtr video would blank out/ q438 open | When playing back a tape the video would go to black screen.was missing sync, burst and composite video, -solution :found q438 opened up when circuit warmed up. | ||
| SONY |
CCDTR80
|
Unit plays with no tape inside / rpl ps500 | Unit goes into play with no tape inside also does not sensereel rotation. found ps500 open | ||
| SONY |
CCDTR73
|
No function at all; no evf / resolder cn504 on the vs125 bd | You hear a beep when changing from vtr mode to camera mode,but no function at all and no evf. found bad cn504 on vs125 board. -solution :resolder cn504 on vs125.- hq comments: cn504 is the connector between the dc to dc converter andthe vs bd. no volt | ||
| SONY |
CCDTR73
|
No eject/ drum ramps up/ replace x502 off of ic505 | When powering up unit will spin the drum and stop. no other functions work. after resoldering ic505 same problem. isolated problemon servo board vc125, and found x502 not oscillating. | ||
| SONY |
CCDTR70
|
Unit plays with no tape inside / rpl ps500 | Unit goes into play with no tape inside also does not sensereel rotation. found ps500 open |