Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY CDXU300
Part # correction: sw654 Service manual correction # 1, page 4, shows a picture ofsw654 used in some production, but the part number listed is for theswitch used in previous production. the switch in the drawing contains anadditional spring-steel switch actuator which is not fo
SONY CDXC590
Removing keyswitches (use pyro-pen jr. on setting # 1) The key switches may be difficult to remove without damaging the pcb.
SONY CDXC590
Keyswitches fail The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha
SONY CDXC490
Removing keyswitches (use pyro-pen jr. on setting # 1) The key switches may be difficult to remove without damaging the pcb.
SONY CDXC490
Keyswitches fail The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha
SONY CDX900
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.
SONY CDX600DSP
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.
SONY CDX600DSP
No fm (replaced tuner pack fe601, p/n a-3282-003-a) No fm on unit.
SONY CDX5490
Removing keyswitches (use pyro-pen jr. on setting # 1) The keyswitches may be difficult to remove without damagingthe pcb.
SONY CDX5490
Keyswitches fail The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha
SONY CDX5470
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.
SONY CDX5460
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.
SONY CDX5290
Removing keyswitches (use pyro-pen jr. on setting # 1) The keyswitches may be difficult to remove without damagingthe pcb.
SONY CDX5290
Keyswitches fail The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha
SONY CDX5270
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.
SONY CDX5260
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.
SONY CDX5090
Removing keyswitches (use pyro-pen jr. on setting # 1) The key switches may be difficult to remove without damaging the pcb.
SONY CDX5090
Keyswitches fail The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha
SONY CDX5070
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.
SONY CDX5060
Test mode error codes explained (see car bulletin # 373) Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode.