Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDTR600
|
No function at all; no evf / resolder cn504 on the vs125 bd | You hear a beep when changing from vtr mode to camera mode,but no function at all and no evf. found bad cn504 on vs125 board. -solution :resolder cn504 on vs125.- hq comments: cn504 is the connector between the dc to dc converter andthe vs bd. no volt | ||
| SONY |
CCDTR600
|
No eject/ drum ramps up/ replace x502 off of ic505 | When powering up unit will spin the drum and stop. no otherfunctions work. after resoldering ic505 same problem. isolated problemon servo board vc125, and found x502 not oscillating. | ||
| SONY |
CCDTR400
|
Individual motor testing using rm-95 | Models such as the ccdtr400 and ccdfx430 do not include themotor test on one of the service procedures, ex, capstan forward andreverse drum forward and reverse etc. | ||
| SONY |
CCDTR400
|
Unit plays with no tape inside / rpl ps500 | Unit goes into play with no tape inside also does not sensereel rotation. found ps500 open | ||
| SONY |
CCDTR101
|
Steadyshot jerked side to side; adjust addresses 12 & 13 | Steady shot jerky | ||
| SONY |
CCDTR101
|
Tdk tapes get stuck | Tape stuck in unit won't eject. | ||
| SONY |
CCDSC5
|
No lcd play / peplace l004 | No lcd operation. fluorescent tube does light up however,no r5 or b out from ic001 to lcd block pd42 board. | ||
| SONY |
CCDFX730V
|
Individual motor testing using rm-95 | Models such as the ccdtr400 and ccd fx430 do not include the motor test on one of the service procedures, ex, capstan forward andreverse drum forward and reverse etc. | ||
| SONY |
CCDFX730V
|
Blue lcd or multi colors or no video in monitor/solder | Had a blue screen and color charged when i flexed board. -solution :re soldered and cleaned ic002 rgb decoder. | ||
| SONY |
CCDFX710
|
No video in camera mode | In camera mode no video in viewfinder and no video on videoout. also data in viewfinder would roll. | ||
| SONY |
CCDFX630
|
When eject tape guides unload halfway then load/ps500 on vs1 | Trying to eject tape guides would come back halfway then loadagain. both in vtr and camera. also when in vtr you could hit play andunit would think there was a tape in mech. | ||
| SONY |
CCCTR83
|
No eject/ drum ramps up/ replace x502 off of ic505 | When powering up unit will spin the drum and stop. no otherfunctions work. after resoldering ic505 same problem. isolated problemon servo board vc125, and found x502 not oscillating. | ||
| SONY |
GDM2036S
|
Shutdown due to q204/h. out failure on d3 pcb | The monitor shut down due to horiz. scan failure. the h.out: q204 and b+/h. size reg.: q217 failed. b+ filter c405 had lowcapacitance. | ||
| SONY |
DD20
|
Won't read disc | Unit would not read. found disc wouldn't turn freely afterloading. removed chucking assy, found small foreign object stuck tomagnet preventing it from gripping disc against spindle. | ||
| SONY |
CPD17SF1
|
Picture unlock with mac 270c powerbook/duo dock | The macview adapter used on 640 x 480 @66 hz video mode ofmac model 270c power book/duo dock system exhibits vert. unlock inpicture. | ||
| SONY |
CPD1425
|
Resistor body shorted to pcb run | |||
| SONY |
CPD1425
|
Tested monitor picture not synched | No synch when connected to team video gen. card. found problem with extender cable, which works for all of our other monitors.tried 6 different cpd1425's. | ||
| SONY |
ICFC25
|
No clock memory back up - check battery connector polarity | No clock back up with a new 9v battery. | ||
| SONY |
CFSW301
|
No am or fm or intermitent - replace cf3 | No radio am or fm or intermittent radio. during mechanicalvibration will be intermittent or off. | ||
| SONY |
SLV920
|
Cracked ma-181 boards on slv-920/770 | Cracked ma-181 found in slv-920/770 models. the symptom my be either no remote operation(crack in left rear corner) or unit in operative at all(crack at center) |