Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
LBTD560
|
Cd drawer won't open - dislogde carousel from spindle motor | Carousel gets caught on spindle motor making it impossible to open the drawer. could be caused by attempting to open the drawer with transport key in. | ||
| SONY |
HCDH605
|
Left channel, no audio - replaced ic401 | Left channel is out on deck a traced audio signal to ic401found no output on pin 8 of ic. | ||
| SONY |
HCDH1200
|
Error reading on display "5c5" - replaced q906 | Display shows 5c5, unit dead. cannot power up, q906defective. 12.6v supply shorted to 5.6v line. | ||
| SONY |
HCDD115
|
No cd functions no display - replace shorted q1139 | No cd functions no display. | ||
| SONY |
HCDC33
|
No power - replace f911,912, resold cold solder on cn905 | No power/ not completely, t/d has some power. | ||
| SONY |
HCDC33
|
Cd doesn't play - realign cd mech | Cd doesn't play. | ||
| SONY |
HCDC33
|
Cd door won't open - inserted and soldered +lead of c178 | Cd door wouldn't open. found c178 positive side lead not inserted thru board. | ||
| SONY |
HCDC33
|
Cd stuck in unit - realigned mech | Cd stuck inside, won't play. | ||
| SONY |
HCDC33
|
No functions on deck b - replaced 7 core wire | Deck b no function don't record, play ff or rew. | ||
| SONY |
HCDC33
|
Tape audio low - resolderd ic901 | Tape a & b sound low. no sound from left speaker. | ||
| SONY |
CDPC445
|
Reads disc,but won't play-solder -lead on sled mot | Unit would read a disc but would not play. found sled was not moving. | ||
| SONY |
CDPC245
|
No audio | Had no audio output on either channel. found input to line amp ic501 only showing a small sawtooth wave in. | ||
| SONY |
CDPC245
|
Intermittent/erratic operation - replace bd board | Several problems recently relating to the units abilityto read and track the disc. the problems are often intermittent anderratic. in these instances the problem has been isolated to poor feedthrough connection on the bd board. there does not seem to b | ||
| SONY |
XRC720
|
Removing keyswitches (use pyro-pen jr. on setting # 1) | The key switches may be difficult to remove without damaging the pcb. | ||
| SONY |
XRC720
|
Keyswitches fail | The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha | ||
| SONY |
XRC620
|
Removing keyswitches (use pyro-pen jr. on setting # 1) | The keyswitches may be difficult to remove without damagingthe pcb. | ||
| SONY |
XRC620
|
Keyswitches fail | The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha | ||
| SONY |
XRC610
|
Removing keyswitches (use pyro-pen jr. on setting # 1) | The key switches may be difficult to remove without damaging the pcb. | ||
| SONY |
XRC610
|
Keyswitches fail | The keyswitches fail. it is most often the select key butcould be any key. sometimes there are more than 1 bad switch on the samefaceplate. -hq comments: the qa group in tokyo has been notified and samples havebeen sent to them. an improved switch ha | ||
| SONY |
XRC520
|
Removing keyswitches (use pyro-pen jr. on setting # 1) | The key switches may be difficult to remove without damaging the pcb. |