Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDPC325
|
Humming noise from inside unit - see s/b hfp381 for mod | Could hear a humming noise usually on tracks 2-6 of cd.replaced optical block 1st time. unit went out and came back again in 45days with same problem amd changing optical block again along withcdx2500bq chip and again flex cable. -hq comments: see s/b | ||
| SONY |
CDP211
|
No audio - ic101 defective | No audio output, but plays disc ok. the -9.5v supply wasmissing from ic306,307 and 271. no oscillation found at ic291 pin 5, so nosignal to be rectified by d292. found no input vid pin 6 of ic291, whichis the wdck signal from ic101 pin 44 going through a | ||
| SONY |
CFD610
|
Disc jam mechanism | Fingers on the disc case (ref 269) warp causing a disc to jamthe mech. | ||
| SONY |
XRU800
|
Switching noise from speakers while volume is being changed | While the volume is being raised or lowered, switching noisemay be heard from the speakers, especially if high power amps or highefficiency speakers are being used. | ||
| SONY |
XRU800
|
Extension cable for repairing display mcb (j-2502-009-2) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRU700
|
Switching noise from speakers while volume is being changed | While the volume is being raised or lowered, switching noisemay be heard from the speakers, especially if high power amps or highefficiency speakers are being used. | ||
| SONY |
XRU700
|
Extension cable for repairing display mcb (j-2502-009-2) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRU660
|
Extension cable for repairing display mcb (j-2502-009-3) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRU550
|
Extension cable for repairing display mcb (j-2502-009-3) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRU500
|
Switching noise from speakers while volume is being changed | While the volume is being raised or lowered, switching noisemay be heard from the speakers, especially if high power amps or highefficiency speakers are being used. | ||
| SONY |
XRU500
|
Extension cable for repairing display mcb (j-2502-009-2) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRU330
|
Extension cable for repairing display mcb (j-2502-009-0) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRU330
|
Face panel doesn't light up (replaced lock assy, ref. 2) | Replaced the lock assy. | ||
| SONY |
XRU220
|
Extension cable for repairing display mcb (j-2502-009-0) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRU220
|
No power (found open trace between q117 emitter & cnp201 -2) | Unit had no display cannot turn on. no function at all.checked all b+. found q117 e gets 10.5 v. but cnp201 pin 2 is 0v. foundpattern foil on main pcb broken. | ||
| SONY |
XRU110
|
Extension cable for repairing display mcb (j-2502-009-4) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRC410
|
Extension cable for repairing display mcb (j-2502-009-8) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XRC210
|
Extension cable for repairing display mcb (j-2502-009-8) | It may be difficult to repair the display mcb without using anextension cable. | ||
| SONY |
XR7070
|
Schematic and mounting diagram errors: ic104 pin 1 location | The print on page 27 of the service manual for the ic104 #1pin related to the actual ic chip is incorrect. the pin #1 is not at thecorner cut. | ||
| SONY |
XR5620
|
Extension cable for repairing display mcb (j-2502-009-8) | It may be difficult to repair the display mcb without using anextension cable. |