Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
BM18
|
Wrong dict lever p/n listed in s/m, use 3-318-289-01 | When ordering above part, it is received without the springhook that couples the dict/listen switch. a hole is drilled and tapped atthis location on the new lever, but no other parts are packaged with it.everything else about the new lever appears ident | ||
| SONY |
XTU500V
|
Buzzing, no audio from tv tuner or vcr, (cd audio ok) | Cd's audio is ok. no audio from tv or video | ||
| SONY |
XRU500
|
Does not accept tape (found cn401 was not seated properly) | Unit would not accept tapes. four screws holding mech were inplace. connector cn401 was not seated properly. | ||
| SONY |
XRU220
|
Intermittent or no turn-on (replaced nose detect s901) | I have seen three units with this problem. the resistance ofthe nose switch, when closed, is in the 200-1000Ω range, inadequate toreliably signal the micro that the nosepiece is in place. | ||
| SONY |
XR5450
|
Reference nos. reversed (ref 11, 12) in early version manual | Reference numbers are reversed for ref. 11 and ref. 12 in theservice manual. | ||
| SONY |
XR2100
|
Part information corrections: knobs | Knobs not available as set as listed in sm. page 22 ref 1. | ||
| SONY |
MDX400
|
Unit won't load/play discs (replaced cables 214, 215, 216) | Unit won't read or play discs. display read please pushreset button. pushing reset produced no change. disassembling mech., ifound all three rotary flex boards pinched and torn in mechanism (ref. 214215, 216). | ||
| SONY |
EXCD50
|
Sw807-sw816 part numbers not in manual (p/n is 1-554-980-31) | Page 32 of service manual is missing switch part numbers. -hq comments: the part number is 1-554-980-31, as shown in servicemanual supplement 1, which is currently being distributed to the field(10/11/94). | ||
| SONY |
CDXU404
|
Loading roller slipping on shaft | Complaint: unit would not pull disc out of pack. saw discwould be pulled to roller and roller gear assy was being driven but rollerwas not turning. found no friction between roller and gear assy. (ref.165). removed old roller, found brown, dry powde | ||
| SONY |
CDXU303
|
Right channel has no audio (replaced lb201) | Cd plays ok, but only left channel has audio (no audio onright channel). found the ferrite bead on the jack board was broken. | ||
| SONY |
CDXA55
|
Proper orientation of jack flexible board | After disassembly of unit to check alignment, unit didnot work and wait appeared on controller. when power was applied, drslider would cycle and when magazine installed elevator would move but notrespond to controls. | ||
| SONY |
CDXA55
|
Dampers and floating chassis damaged during shipping | Noticed all late model changers have been suffering damper &chassis damage during shipping. this is due to the fact that a method oflocking the floating mech was not included in the design. noticed newmodels lack the same provision for reducing or eli | ||
| SONY |
CDX900
|
No cd play (replaced q681 and undocumented 2.2 ohm resistor) | No cd play. no motor movement upon disc insertion, displayreads reset. | ||
| SONY |
CDX5470
|
Erratic behavior on amp remote | When accessory lead is switched off, amp remote lead goes lowfor 5 seconds, then switches high for 5 seconds while producing a beep,then goes low. | ||
| SONY |
CDX5460
|
Loses power intermittently (replaced r536 p/n 1-216-073-00) | Power would cut out when input dc voltage would drop below14 volts. found r536 to be a 50kΩ resistor instead of 10k. | ||
| SONY |
CDX5260
|
Sensitive to vibrations, found damper shafts broken, ref 117 | Unit skips very easily if it plays at all. | ||
| SONY |
CDX5060
|
Lock will not hold face plate (re-positioned small spring) | Face plate will not lock onto unit. appears lock is broken.closer inspection revealed smaller spring misaligned. | ||
| SONY |
CDX5060
|
No functions/no power (replace ic503, p/n 8-759-167-50) | Unit had no functions or power. found ic503 overheating dueto short. | ||
| SONY |
CDX4050
|
Sw807-sw816 part numbers not in manual (p/n is 1-554-980-31) | Page 32 of service manual is missing switch part numbers. -hq comments: the part number is 1-554-980-31, as shown in servicemanual supplement 1, which is currently being distributed to the field(10/11/94). | ||
| SONY |
CDX35RF
|
Not changing discs (replaced ic601, p/n 8-759-085-35) | Unit initialized ok and played disc one ok but when anotherdisc is selected display showed e99. note: 1, mech moved up/down as ininitialize state, not trying to go to disc position. 2, ev sensor ok,when disconnected ev moved up. |