Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDX5060
|
No functions/no power (replace ic503, p/n 8-759-167-50) | Unit had no functions or power. found ic503 overheating dueto short. | ||
| SONY |
CDX4050
|
Sw807-sw816 part numbers not in manual (p/n is 1-554-980-31) | Page 32 of service manual is missing switch part numbers. -hq comments: the part number is 1-554-980-31, as shown in servicemanual supplement 1, which is currently being distributed to the field(10/11/94). | ||
| SONY |
CDX35RF
|
Not changing discs (replaced ic601, p/n 8-759-085-35) | Unit initialized ok and played disc one ok but when anotherdisc is selected display showed e99. note: 1, mech moved up/down as ininitialize state, not trying to go to disc position. 2, ev sensor ok,when disconnected ev moved up. | ||
| SONY |
CDFX430
|
No power/resolder cn504 | No power. -solution : resolder cn504. | ||
| SONY |
CCDV5000
|
Unit shuts down when using battery/replace ic103 | Unit ran fine on ac adaptor but would not ooperate withbattery. tech was not able to perform battery down adjustment, no matterwhere set unit shut down at 6.3 volts. battery sense line at themicroprocessor was changing when rv001 was adjusted at pin 4 | ||
| SONY |
CCDTR81
|
Technical flash 89 part is incorrect | Tech flash states that part a7048534a (e) was used. | ||
| SONY |
CCDTR71
|
Mode switch | Mode switch bad, mode switch is not available separately. theone way to repair is to replace entire chassis , #301.can you locate a part for mode switch separately. tr5 has part # but idon't know if it is the same. -hq comments: because of the high pr | ||
| SONY |
CCDTR21
|
Intermittent 5 min warning/check soldering on cn521, w522 | 5 min warning would intermittently show in v.f. even withfully rewound tape. couldn't reproduce problem on bench. -hq comments: please check the soldering on cn521 and w522 on the sl-27board. | ||
| SONY |
CCDTR101
|
No evf video after warm up/replace q304 | After 10-15 minutes of camera or vtr mode evf video goes out. | ||
| SONY |
CCDSC5
|
Spring does not come with tg1 | Diagram on pg 121 of ccdsc5 manual shows tg1 arm with thespring. the part does not come with the spring. | ||
| SONY |
CCDFX430
|
Lanc jig problem | Servicer changed vs-110 mcb due to soldering problems withic505 and ic503. found board was locked in forced power mode. theprocedure in the manual was confusing, but we found by setting powerswitch to vtr side while setting addresses 02 and 03 to data 00 | ||
| SONY |
CCDFX420
|
Picture in playback cuts in and out | Picture in playback will cut out/in. solution: replace ic501. | ||
| SONY |
CCDF77
|
No capstan lock | The capstan speed was not locked. found c562 leakingelectrolytes to board. solution: cleaned board and replaced capacitor. submitted by a. blitz/sound advice. | ||
| SONY |
CCDF55
|
No video from camera block/resolder w801 | Technician replaced dt and mx boards for no video problem,camera block. no video output frompins 24/25 of the mx board. all inputsignals were correct, including clamp pulsed. yh in, and xdl1,2. | ||
| SONY |
CCDF55
|
Evf part number (for m0495) | Ccdf55 may use a round crt or a square crt. the crtholders are therefore, different. | ||
| SONY |
CCDF35
|
No video from camera block/replace c704 (leaky) | Techn replaced ic606 for no video problem from camera section. signals were correct at inputs of the encoder ic (yh, yl, r-y, b-y) andat output pins 10 (y) and 24(c). signal became distorted and erratic atq602. collector had little noise on it (b+ line | ||
| SONY |
PIC1000
|
Vertical bar across password screen with incoming calls | |||
| SONY |
MZ1
|
Unit locks up after 13 secs in rec (replaced s705) | Unit went into rec and display would lock up at 13 secs. tocedit never showed up. also, when stop pushed, unit would totally lock up. | ||
| SONY |
MZ1
|
Int. no play, int. lock up (replaced power board, ref. 79) | Unit heats up over time & will lock up during play or rec.may take 4-5 hours to show up. | ||
| SONY |
MDW60
|
Possible defective mdw60's | The enclosed three (3) mdw60's (lots a111902m, a111292m,a111502m) jump sectors on rec/pb. the unit they came in withplays/records all other disc's w/o problem. -hq comments: the samples played/recorded o.k. on 2 units we have in thelab (1 was a product |