Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
ITD100
|
Programming on lower set of memory | Complaint is: cannot program lower number slots. if wefollow manual's instructions, it doesn't work and we get error beep.customer had bought this unit last month and he tried manual instructionswhich did not work. | ||
| SONY |
ITA555
|
Answering machine portion of unit dead | With ac adaptor plugged in, led601 (conv rec) and led602(memo) were lit all the time. there was no operation of ogm record set-up,and no tape functions. the b+ to motor was very low from ic610/ pin 12. | ||
| SONY |
ITA555
|
Poor audio when play back of icm | In this type of unit customer complains about audio on icmthat is very poor or unclear or unable to hear icm. | ||
| SONY |
ITA555
|
Unit has combination rec/pb/erase head | The service manual, page 41, shows 2 heads, erase andrecord/play. this unit has a combination record/play/erase head.servicer needs a part number for the r/p/e head. -hq comments: tokyo was contacted. the part number of the rec/play/erasehead is 1-500- | ||
| SONY |
ITA505
|
Poor audio on icm play back | Complain about playback is very poor or unclear audio. | ||
| SONY |
GV500
|
Ref 122 no longer available/ order individual parts | Part # for complete light unit show invalid in both wrpc andnpc. what is correct part#? | ||
| SONY |
GV500
|
No audio/replace f102 | No audio out (speaker). unit is used with camera. | ||
| SONY |
TCWR87ES
|
Recording doesn't work on left side - c122 defective | C122 on the main board defective causing lost signal gain.i did change the playback/record head, it didn't solve the problem.i found c122 defective. | ||
| SONY |
TCFX320
|
Motor replacement per sb 199 | Servicer was replacing capstan motor as per s/b 199. whenpower was applied the fuses opened along with a couple of resistors onthe board. the servicer checked the new motor and it checked fine. heopened the motor and found that one terminal on the ins | ||
| SONY |
TAAX401
|
Part installed backwards in new main board | C805 was installed backwards on new board from kc (a4334260a). | ||
| SONY |
STRGX99ES
|
On screen display problem - display indicates feature n/a | When on screen on/off button is put on the display readsthis model does not offer this feature. -hq comments: we were not able to obtain any additional information fromthe authorized servicer. the unit was returned to the dealer. we willconsider this | ||
| SONY |
STRGX909ES
|
Unit goes into protect at power on - resoldered t902 | Unit goes into protect on as soon as power applied.checked the voltage of all the outputs of amp section. all are normalincl. ground. i found the unit not tuning on fm during scan. thisoccurred during the first 3 seconds before protection on. | ||
| SONY |
STRD990
|
Unit will not turn off - resoldered jumper wire | The unit would turn on when power was applied. the mute lightwas always on. all front panel controls work, but there is no audio andunit will not turn off. | ||
| SONY |
STRD990
|
Tuner bleed when using other inputs - use s/b 225r1 | Also s/n 8863992. units have tuner noise when listening toother inputs at volume level 2 and up. noise increases as volume isturned up. please provide remedy. -hq comments: please try the strav920/1020 modification (s/b 225r1).it transfers to the strd9 | ||
| SONY |
STRD611
|
Unit appears dead - volume control bd unplugged | Protect light comes on, or unit appears dead. volume controlboard unplugged from main board. | ||
| SONY |
STRAV770X
|
Rt. channel level meter low - c660 changed value | Unit had low level display of right channel signal, althoughsignal was ok. input to ic602 pin 5 was normal but pin 7 had significantlylower output than pin 1 (left out). ic did not resolve problem. | ||
| SONY |
STRAV23
|
Defective new replacement front panels - tuning buttons | The majority of the new front panels being received havedefective preset tuning buttons. the preset tuning button brackets arenot being secured properly to the front panel during manufacturing. thefastening pegs are not being heated and pressed flat. | ||
| SONY |
MHC1600
|
Cd synchronize feature does not function when micon changed | When replacing main bd, bd bd or ic micon upd75116gf, thecd synchronize feature will not operate on the models shown below: cdp-h3600 main board or ic201 with jw202 or bd board or ic202 hcd-h1600 bd board | ||
| SONY |
MDS101
|
"disc error" displayed (replace opt. assy, p/n 8-583-003-21) | Display reads disc error and then ejects the disc (it willtry reading the disc for about 10 seconds then ejects). when i faked theunit into the loaded position without a disc the sled would go to thehome position but would not focus search. i checked th | ||
| SONY |
HSTH1750
|
Slight hum in background - c601,602,623,624 opened | Slight hum noticed in background. |