Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDX5460
|
Will not load cd (replace sw1, p/n 1-571-754-31) | Found sw1 broken. replaced switch and unit workednormally. | ||
| SONY |
CDX5260
|
Will not load cd/grinding noise (straighten ref. # 10) | When cd is loaded into unit, load will flash for about fiveseconds, and there will be a grinding noise before cd is ejected. | ||
| SONY |
CDX5260
|
Unit stays in test mode (replace ic501, p/n 8-759-167-49) | When powered up, display of unit goes through test modefunction. reset has same effect. when am, fm or cd is selected, unitgoes through corresponding test mode function. | ||
| SONY |
CDX5260
|
No display (replace d501, p/n 8-719-921-82) | The leds and display are not lit. found d501 shorted. | ||
| SONY |
CDX5260
|
Cd does not want to load (resolder d802) | When cd was inserted, unit would not power up and take cdunless it was pushed in manually almost half way. | ||
| SONY |
CDX5180
|
Improving clock accuracy | The clock gains or loses up to 3 minutes per month. -solution (tech. news me-93035): change x501 to part # 1-579-886-11.replace c506 and c520 with part number 1-163-229-11 (same part asoriginal, part is improved. -see car stereo bulletin # 315. | ||
| SONY |
CDX5060
|
No display (replace d501, p/n 8-719-921-82) | The leds and display are not lit. found d501 shorted. | ||
| SONY |
CDX5060
|
Will not load cd/grinding noise (straighten ref. # 10) | When cd is loaded into unit, load will flash for about fiveseconds, and there will be a grinding noise before cd is ejected. | ||
| SONY |
CDX5060
|
Unit stays in test mode (replace ic501, p/n 8-759-167-49) | When powered up, display of unit goes through test modefunction. reset has same effect. when am, fm or cd is selected, unitgoes through corresponding test mode function. | ||
| SONY |
CDX5060
|
No power (replace x502, p/n 1-579-886-21) | Unit had no power and would not even reset. | ||
| SONY |
CDX5060
|
No audio from speakers (replace c572, p/n 1-135-159-21) | Unit has audio from pre-amp output but not from speakers. ampb+ line from ic503 to ic701 was being held low. | ||
| SONY |
CDX5060
|
Faceplate won't lock on unit (re-install screw in lock assy) | Front panel will not lock onto front of main unit. | ||
| SONY |
CCDVX3
|
Poor color recording/check cn001, cr42 board | Although e-e color was always fine, the chroma was not beingrecorded properly intermittently. | ||
| SONY |
CCDV9
|
Dead/replace f952 and c619 | Unit dead, blown fuse f952. | ||
| SONY |
CCDTR91
|
Solarization of camera picture/replace ic604 | Camera e-e picture was solarized. checked outputs from analogto digital converter and found 3 line inactive. | ||
| SONY |
CCDTR81
|
No e to e video in camera mode/replace ic301 | No etoe in camera mode. | ||
| SONY |
CCDTR81
|
No camera video shuts down in 2 seconds/replace ic 853, ld42 | No camera video powers up for 2 seconds then shuts off. cam4.9v (cn852 pin 26) shorted. | ||
| SONY |
CCDTR7
|
Distorted pix/replace c180, vs61 board | Unit would not playback properly. traced problem to docpulse. this signal comes from pin 13 of ic101 head amp. pin 10 of ic102had no output which supplies the other half of the waveform to ic101pin 12, required to develop the doc pulse. | ||
| SONY |
CCDTR500
|
Caution indication/replaced loading motor | Wouldn't load tape and caution indication present. foundloose item 172 base assy causing mechanism jam. also, found a bad loadingmotor damaged by the mechanism malfunction. | ||
| SONY |
CCDTR31
|
Noisy playback as if heads are clogged/check l160, vs board | In vtr mode playback looks as if heads are clogged. videocomes in and goes out etc. |