Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDTR31
|
Camera "flickering" cam and play modes/check fp572 soldering | Camera picture flickering in all modes. | ||
| SONY |
CCDTR21
|
No video pb/check l160 | No video in pb e to e ok. looked like a very dirty head. ihad some video in pause. | ||
| SONY |
CCDTR200
|
Missing part in crank arm assy -see small part cam0304 | In the dotted line in the crank arm assy is a small part.what is the part # for this? it was misplaced. see attached bulletin. -hq comments: please order x-3941-902-1, and take the hinges from thispart. | ||
| SONY |
CCDTR101S
|
Solarized camera picture/replace ic802 | Solarization problem in camera mode. also with this sameproblem, i found a different unit same model that when in e to e cameramode output is all white screen. | ||
| SONY |
CCDTR101
|
White specks in e-e/replace core ic708 | In e-e mode, the picture had white specks all over screen.there was not enough distortion to see on video signal on scope. | ||
| SONY |
CCDTR101
|
Horizontal interference along bottom of picture/check x801 | In camera and vtr mode there is a horizontal interferencealong bottom portion of picture. once warmed up its very obvious. | ||
| SONY |
CCDTR101
|
Gear on motor splits/replace motor 1-541-607-21 | No mechanical motion. | ||
| SONY |
CCDSC5
|
No record audio. ok on playback/replace mic | No record audio. playback audio ok. | ||
| SONY |
CCDSC5
|
Will not eject (possibly dropped)/check ref 817 | Will not eject, motor noise found loading motor gear out ofplace plastic holder appears to be weak and not able to handle multiplesloading-unloading functions. | ||
| SONY |
CCDFX420
|
No camera video/check ic704 | No camera video in standby playback video and audio ok. | ||
| SONY |
CCDF70
|
Camera mode, video has streaks and flares in high lite areas | When camera is directed towards high brightness or brightlight, shows vertical streaks in video. these streaks off of main power supplyof brightness in picture can start at top of picture to bottom or smaller. attempted to adjust v-sub but voltage nor picture | ||
| SONY |
CCDF55
|
Irregular capstan speed/check connector fp-248 | Intermittent speed up of the capstan motor. | ||
| SONY |
CCDF55
|
Dead/replace f991 and c317 (va46 board) | Dead unit. f991 open. short circuit on video 4.9v line. | ||
| SONY |
CCDF35
|
Low or no audio in pb or cam mode/check c420, co2 board | Low or no audio from vtr or cam mic. checking voltages aroundq402-q404 found voltages wrong for pb or cam mode. | ||
| SONY |
CCDF30
|
No eject due to no drum start/replace q053, ss-86 board | Unit never had any drum start so therefore didn't have anycapstan. when you go into eject in play mode the drum pwm start pluse outof pin 5 of ic001 would go from ov to 5v. this pulse was input to thebase of q053 turning the transistor on, but the coll | ||
| SONY |
GEN-MON
|
Proper method of performing focus on computer monitors | Performed focus using the service center generator but,customer still claims that the unit is not focused sharply on theircomputer. -hq comments: traditionally we performed focus on a dos type screen(black background and white character foreground). but | ||
| SONY |
GDM2038
|
Picture is unstable when changing from text to graphics mode | |||
| SONY |
GDM2036S
|
Picture is unstable when changing from text to graphics mode | |||
| SONY |
GDM2036S
|
No high voltage, and no hsync due to ic101 (h osc) | All power supply voltages are ok but, no horizontal drivesignal from ic101. | ||
| SONY |
GDM1936
|
Picture is unstable when changing from text to graphics mode |