Sony Repair Tips
Search: sony
Results: 20075
Results: 20075
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
SPP115
|
Id rom defective | New id rom received from npc is defective. this is the secondtime this has happened. | ||
| SONY |
TCFX110
|
Missing part number for record lever | Need the part number of the record lever on the top left corner of ref. no. 81 on page 13 of s/m. i ordered the chassis assembly 4-894-968-01, but it does not come with it. please help. | ||
| SONY |
CDPC205
|
Intermittent spindle motor start | Spindle motor has to be given a little push in order to get upto speed. | ||
| SONY |
KV25XBR
|
No video/switching problem | There was no video displayed on the screen or present at themonitor out jack. sound was ok and characters were present. we found theproblem to be caused by an open pull up resistor r-913 u board. thisprovides bias for ic-805/video switching and the vi | ||
| SONY |
KV27XBR10
|
No picture, micro locked up, replaced diode cp111 on pin 36 | No picture only snow. ic-101 on the a board is locked up. | ||
| SONY |
SLV757UC
|
Lost of contrast in loop through | When the playback output signal of another unit is loopedthrough the slv-757uc, the picture looses contrast. | ||
| SONY |
KV20TS20
|
No audio in tv mode, replace sw q-1444 on "u" board | Audio signal was present at pin 11 but not at pin 10 of audioselect ic-1406 (u-board). | ||
| SONY |
CCDF55
|
Part number for u' mechanism drum base assembly | What is the part number for the u' mechanism drum baseassembly? | ||
| SONY |
SPP320
|
Low line signal | Low line signal. | ||
| SONY |
SLV575UC
|
Won't play - shuts down | Pinch roller assembly is out of timing with tape mechanism. | ||
| SONY |
XM3520
|
Protection mode always active | Unit stays in protection. | ||
| SONY |
SLV575UC
|
Unable to set the time | It would be helpful to have more complete information on theinternal function of ic-201 as a troubleshooting tool. a 32.8k clock ismissing. -hq comments: please check the 32khz crystal x202. | ||
| SONY |
MVCA10
|
No rf search | No rf search or randomly goes to a position where the tracknumber does not match the picture content. | ||
| SONY |
WMF2078
|
No audio from tape or tuner, opr/batt led does not light | Opr/batt light does not come on in tape or radio. no audio.there is power to the deck. | ||
| SONY |
TCU270
|
Set can't function without power supply; jig doesn't work | We needed an 18 vac center ground tap power supply to testthis unit. our shop jig would not work. i ordered the power transformerfrom the avu-270 model, wired a/c to the input and used the 18vct windingto power the tcu-270. the windings (secondary) vo | ||
| SONY |
SLV555UC
|
Lost of contrast in loop through | When the playback output signal of another unit is loopedthrough the slv-555uc, the picture looses contrast. | ||
| SONY |
XR7300
|
Missing part number, knob (handle fitting) | The lift tab on the handle (knob, handle fitting) does notcome with the new handle and most service manuals do not have the partnumber listed. | ||
| SONY |
XR5507
|
Missing part number, knob (handle fitting) | The lift tab on the handle (knob, handle fitting) does notcome with the new handle and most service manuals do not have the partnumber listed. | ||
| SONY |
XR4057
|
Missing part number, knob (handle fitting) | The lift tab on the handle (knob, handle fitting) does notcome with the new handle and most service manuals do not have the partnumber listed. | ||
| SONY |
UP850N
|
Printer is noisy when using upp-110hd paper | When upp-110hd paper is used, the unit squeaks and makes loudnoises like old typewriter striking the roller. when you use the upp-110spaper, everything is quiet. the only difference between the paper is theupp-110hd has a shiney surface. we are going |