Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SONY |
STRGX90ES
|
Not radio | Fm display is fine. signal strength is always indicating afull (strong) signal. no fm stations are received. checking pin 2 cn-03,no ground. | ||
SONY |
FD500
|
No power, open f602, check customer's ac adaptor | No operation, no power or no audio power ok. this seems to bean on going problem or just failures of last production runs. | ||
SONY |
CCDV5
|
No camera video | No camera video, zoom and af work ok. camera video present onv4-8 pin 54, not at pin 3. checked for +5 volts on vy-8 board - notthere. | ||
SONY |
TCM858
|
Background noise (hiss) in record mode | Background noise (hiss) in record mode when there is no soundin the room. customer wants to know if this is normal? -hq comments: no this is not normal. if the hiss is heard during therecording mode, then it is definitely not normal as the ground retu | ||
SONY |
CCDTR4
|
No video in camera or playback | When in camera mode or vtr mode, there is no video in view-finder or video out. | ||
SONY |
SPP115
|
Id rom defective | New id rom received from npc is defective. this is the secondtime this has happened. | ||
SONY |
TCFX110
|
Missing part number for record lever | Need the part number of the record lever on the top left corner of ref. no. 81 on page 13 of s/m. i ordered the chassis assembly 4-894-968-01, but it does not come with it. please help. | ||
SONY |
CDPC205
|
Intermittent spindle motor start | Spindle motor has to be given a little push in order to get upto speed. | ||
SONY |
KV25XBR
|
No video/switching problem | There was no video displayed on the screen or present at themonitor out jack. sound was ok and characters were present. we found theproblem to be caused by an open pull up resistor r-913 u board. thisprovides bias for ic-805/video switching and the vi | ||
SONY |
KV27XBR10
|
No picture, micro locked up, replaced diode cp111 on pin 36 | No picture only snow. ic-101 on the a board is locked up. | ||
SONY |
SLV757UC
|
Lost of contrast in loop through | When the playback output signal of another unit is loopedthrough the slv-757uc, the picture looses contrast. | ||
SONY |
KV20TS20
|
No audio in tv mode, replace sw q-1444 on "u" board | Audio signal was present at pin 11 but not at pin 10 of audioselect ic-1406 (u-board). | ||
SONY |
CCDF55
|
Part number for u' mechanism drum base assembly | What is the part number for the u' mechanism drum baseassembly? | ||
SONY |
SPP320
|
Low line signal | Low line signal. | ||
SONY |
SLV575UC
|
Won't play - shuts down | Pinch roller assembly is out of timing with tape mechanism. | ||
SONY |
XM3520
|
Protection mode always active | Unit stays in protection. | ||
SONY |
SLV575UC
|
Unable to set the time | It would be helpful to have more complete information on theinternal function of ic-201 as a troubleshooting tool. a 32.8k clock ismissing. -hq comments: please check the 32khz crystal x202. | ||
SONY |
MVCA10
|
No rf search | No rf search or randomly goes to a position where the tracknumber does not match the picture content. | ||
SONY |
WMF2078
|
No audio from tape or tuner, opr/batt led does not light | Opr/batt light does not come on in tape or radio. no audio.there is power to the deck. | ||
SONY |
TCU270
|
Set can't function without power supply; jig doesn't work | We needed an 18 vac center ground tap power supply to testthis unit. our shop jig would not work. i ordered the power transformerfrom the avu-270 model, wired a/c to the input and used the 18vct windingto power the tcu-270. the windings (secondary) vo |