Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CFSW501
|
Fm not tuning standard 88-108mhz band | After replacing ic-601 (controller) the set would not tune thestandard fm band. it tuned from approximately 65mhz-90.1mhz only. | ||
| SONY |
CCDV701
|
Part number for ir receiver | What is the part number for the ir receiver ic sbx1619-51? | ||
| SONY |
WMF80
|
Band selection knob part number is wrong | Servicer ordered knob by number in manual. could not accesstv mode due to physical obstruction. parts fiche says this is for awm-f77. there is another part number 3-335-732-01 with a description ofknob (c), tuning, that the parts fiche claims to be pa | ||
| SONY |
CDPC505
|
Drawer won't open | Drawer won't open. +10 voltage is low at ic-903 pin 1. | ||
| SONY |
KV32XBR15
|
Buzzing on channel 11, add attenuation | Buzzing noise on channel 11 (sunshine cable) which gets worsewhen srs system is on. tried a working kv27xbr in customer's home and italso does the same thing. customer had another brand name set which ihooked up to the same cable outlet and had no prob | ||
| SONY |
CCDF77
|
Service mode error codes erroneous | Old error codes were not erased from memory by previousservicer. this is contrary to instructions on page 58 of supplement no.1 which states be sure to rewrite the addresses from 20 to 26 to data 00after the operation. this provided erroneous first (or | ||
| SONY |
ITA305
|
Battery does not fit correctly | This is a replacement battery. the legs are too wide to mountin the board. | ||
| SONY |
ITA205
|
Battery does not fit correctly | This is a replacement battery. the legs are too wide to mountin the board. | ||
| SONY |
ITD150
|
Defective keypad | Keypad is defective 7, 8 and 9. redial and mute will notfunction. jumper pushed through board. | ||
| SONY |
ITD100
|
Low dial tone | Low dial tone - zener diode zd-311 is leaking. | ||
| SONY |
SPP50
|
Unit disconnects line after 20 seconds. | Unit disconnects line in approximately 15 to 20 seconds. thisis due to the fact that ic-1 pin 14 is internally shorted to ground (at743Ω). this in turn holds ic-5 pin 20 low and the micro disconnectsthe line. | ||
| SONY |
SPP50
|
No dial tone | No dial tone. z-1 is shorted. credit also b. kennedy for assistance with for. | ||
| SONY |
CCDF33
|
Incomplete "f" ring assembly | Servicer ordered replacement front lens assembly because lenswas broken. part received was ring without lens. the price we sell thepart suggests that the lens is included. the drawing in the service man-ual also indicates the lens is included. please | ||
| SONY |
SLV575UC
|
Capstan motor always runs | Capstan motor always runs fast. ic-501/71 (capstan stop) highin eject mode. q-423/c low, but about 3vdc still applied to motor. | ||
| SONY |
HVR200
|
Need part number | |||
| SONY |
SLVRV5UC
|
Unit won't turn on - intermittent | Unit won't turn on - intermittent. no functions work when acpower fluctuates. | ||
| SONY |
KX2501
|
Jail bars in picture, replaced c-667 | Jail bars vertically in picture. traced ripple to +12 voltline on board pcb with oscilloscope then traced it to an open c-667 the15 volt filter for the 12 volt supply from the switched mode supply. | ||
| SONY |
KV1396R
|
Tiny glitch moving upward in picture, replaced c525 | Tiny glitch moving upward in picture. its barely noticableexcept on straight edges. approximately 1.0 volt ripple measured attp-85. | ||
| SONY |
SL2000
|
Capstan servo will not lock on cold start | Capstan servo will not lock. adjusted capstan free speed andfg amp. unit will play all day with no problem. the next morning thesame problem occured. i thought the problem was heat related. sprayedfreeze mist and found ic-412 and ic-408 very sensiti | ||
| SONY |
CDXR79
|
Will not eject | Ratcheting noise when unit is trying to eject. |