Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
ITD150
|
Missing part number for bz1 and bz2 | There is no part number for the buzzer bz1 in the servicemanual. -hq comments: the buzzer bz1 is not available as a separate item.however it is a part of the lower cabinet assembly. therefore, if you needto replace bz1, you will have to replace the lowe | ||
| SONY |
ITD200
|
Missing part number for bz1 and bz2 | There are no part numbers for bz1 and bz2 in the servicemanual. -hq comments: the 2 buzzers bz1 and bz2 are not available as separateitems. however they are part of the lower cabinet assembly.therefore, if you need to replace bz1 or bz2, you will have t | ||
| SONY |
ITD100
|
Missing part number for bz1 | There is no part number for bz1 in the service manual. -hq comments: the buzzer bz1 is not available as a separate item.however it is part of the lower cabinet assembly.therefore, if you need to replace bz1, you will have to replace the lowercabinet ass | ||
| SONY |
SLV676UC
|
No hi speed rewind on tapes less than t-120 | If a tape less than length t-120 is used, you cannot go intohi speed rewind, only normal rewind speed. it seems like there is a soft-ware problem. -hq comments: this is normal. the system is programmed to enter the highspeed rewind only when it sees th | ||
| SONY |
SLV676UC
|
Index | Went to a customer's home and he showed me a design problem.if you use a tape less in length than at-120 and index 3 or 4 times with3 minute spacing, it will not stop until it sees the first index. thisoccurs only in reverse. foward direction it stops | ||
| SONY |
ITD250
|
Missing part number for bz1 and bz2 | There are no part numbers for bz-1 and bz-2 in the servicemanual. -hq comments: the 2 buzzers bz1 and bz2 are not available as separateitems. however they are part of the lower cabinet assembly.therefore, if you need to replace bz1 or bz2, you will have | ||
| SONY |
KV5300
|
Handle brackets | Bracket which holds the handle is not shown or listed in theservice manual. please let us know the part number. -hq comments: part number for the bracket is 4-361-411-01. | ||
| SONY |
CCDTR5
|
Intermittent poor picture quality - noise in picture | Replace q-107 in head assembly circuit. -hq comments: thanks for the information. q107 is the channel 1a recordswitch. | ||
| SONY |
CCDTR6
|
Will not load, eject or play | No cap. vs from dd-31 board. | ||
| SONY |
EVS550
|
No operation | No functions - display and leds flash. | ||
| SONY |
KV32XBR50
|
No picture, only character display, check the ik line | Sometimes at turn on the screen was black but would show theon screen display. turning up g-2 revealed a barely visible rasterexhibiting extreme pincushion distortion. also, three retrace lines at thetop of screen caused by improper data buss activity. | ||
| SONY |
CDP291
|
Intermittent static in audio | Intermittent static in audio (especially in high frequency). | ||
| SONY |
KV2791R
|
Shut down, replace r-507 | When the brightness and picture controls are high, pin 6 ofic-301 would drop to 2v, then the set would shut down. | ||
| SONY |
DTC300ES
|
No display | Minus 24 volt power supply fails. gary in costa mesa showedme one that had all three components defective. -24 volts is lost whenq-908 and q-907 short, this i think causes c-915 to open. gary says thisis the second unit he has had with this problem. | ||
| SONY |
KV27XBR15
|
Dead, replaced q-503 and repaired cold solder joints | Unit was dead, found shorted h output transistor andcold solder joints on h. drive transformer. | ||
| SONY |
KV20EXR10
|
Low brightness, resoldered r-741 ("c" board) | Very low brightness. looks like color only. rgb pulses arevery low. r-741 leads were not penetrating completely through the boardcausing misoperation of q-711 thus sending a wrong ik pulse to pin 25 ofic-301. | ||
| SONY |
STRD2020
|
No left channel audio | No left channel audio. traced audio back to ic-307 still didnot have audio. went to ic-301 pins 2 and 27 had audio. thought ic-301or ic-307 had to be bad because the digital path was still sending rightchannel audio throughout digital 1 pcb until it b | ||
| SONY |
KV32HSR10
|
Shuts down, "f" board q-651 e-b open | Shut down. found b+ 135v running between 136 and 142vdc. iknew either the load was open or our b+ was not regulating. removed the fboard from the tv and jumped ry-601. i used a 60 watt lightbulb as my loadon the +135 volt line. using the variac while mo | ||
| SONY |
CDPC201
|
New spindle motors are bent | Vertical jitter on rf waveform (eye pattern) after spindlemotor replacement. this is caused by a bent spindle shaft. there is nopacking material to protect the spindle shaft. out of the last ten motorsreplaced, 6 were noticeably bent but could be used | ||
| SONY |
KV27TW71
|
Dead, replaced c-550 | Set was dead. inspection of waveforms at base of q-550, hori-zontal drive transistor was about 1vpp. service manual shows 4vpp. |