Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
WMF76
|
No sound when using tape | Tape is running but no sound. radio works ok. service manualon page 18 mark two part number for q-602. | ||
| SONY |
DTC700
|
Sound mutes intermittently - sometimes will not play | Sometimes the drum motor would not start. other times theunit would mute because of unstable rf envelope. | ||
| SONY |
FH10W
|
Incorrect part number, hp901, hrp901 | The part number shown in the service manual for hp901 andhrp901 is incorrect. the head that is received when part number8-825-505-01 is ordered does not penetrate the cassette shell deep enoughto allow proper head to tape contact. -hq comments: tokyo h | ||
| SONY |
KV27TX12
|
Need p/n for speaker bracket | Need to acquire the speaker mounting bracket. this part islocated on page 38 of the service manual below number 56, but no partnumber is given. -hq comments: this part is not stocked as a replacement part. we checkedthe vendor, but they did not have any | ||
| SONY |
ITD200
|
Part numbers of ref numbers 57 and 58 | The part numbers for the conf and hold buttons, ref # 57 and58 are not listed in the service mabual. | ||
| SONY |
EVS1
|
No tuner/timer operation | No tuner operation, but tape will load and play. | ||
| SONY |
ITA850
|
Short ogm playback | After ita answers, no ogm playback to caller. q-505 pushed through the pc board. | ||
| SONY |
TAU10
|
Icm timing failure | Approximately 15 seconds into incoming message recording, theunit disconnects the line. | ||
| SONY |
DTX10
|
Schematic discrepency: d-d converter +7.5 volt line | There is obviously something missing or drawn erroneously onthe power board schematic (page 46 of the service manual, coordinates m35). the 7.5v line (pin 7) is shown as being directly connected tothe 12v backup line (pin 1). what is the correct route | ||
| SONY |
SLHF900
|
Sub chassis assembly part number | Service bulletin indicates new part number is a x-3691-643-3.this new part has two additional posts on it which will not allow it to beused. our technician in san bruno said he removed both of these at onetime when he repaired this unit. servicer claim | ||
| SONY |
RMP301
|
Remote won't program | When using learn function after successfully programming 2buttons the unit ceases to function. upon reset/program clear unable tore-program, even first two buttons which were initially programed. | ||
| SONY |
KV19TR20
|
Weak sound, replace c-252 on "k" board | Weak sound. | ||
| SONY |
KV32XBR10
|
No power, resoldered q-602 ("f" board) | Set won't come on. | ||
| SONY |
KV13TR20
|
No picture, replaced d-513 | No picture | ||
| SONY |
KX2501A
|
Retrace lines on picture, replaced r-704 | Retrace lines in picture. | ||
| SONY |
KV19TR20
|
Dead (no hv), repaced q-550 h drive tr | No hv. | ||
| SONY |
STRAV220
|
No display or output | No display or output although click of relay can be heard whenunit is switched on. | ||
| SONY |
STRAV720
|
Noise (output) all the time in one channel video/audio out | Noise (output) audible on one channel of audio output whenvideo 1 input selected. | ||
| SONY |
TAE1000ESD
|
Unable to select any input except tuner | Only input available is a muffled tuner. you are able toselect different inputs with front panel controls. panel shows new requestbut audio does not change. | ||
| SONY |
CCDTR7
|
Holder block assembly for ccdtr7 | Is there a part number for the holder block assembly for theccdtr7? there is a part number for the ccdtr5 holder block (ref no. 151in the tr5 manual), but it does not have the eject springs (ref. no. 157and 153 in the tr7 manual) included, and there are |