Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY SLV676UC
Part number of cassette door The service manual page 85 cassette door shown in drawing asnot supplied. this part breaks. substitution could be used if printingon other models with different features was not on the door. had to takedoor from another unit to satisfy customer. -hq
SONY SLV575UC
Part number of cassette door The service manual, page 85 cassette door shown in drawing asnot supplied. this part breaks. substitution could be used if printingon other models with different features was not on this door. had to takedoor from another unit to satisfy customer. -h
SONY EVC8
Chews tape intermittently Unit will chew tape, highly intermittently. found the greaseon the shaft of the b gear assembly to be very sticky. it seems that asthe unit ages the grease thickens and restricts the rotation of the gear.
SONY EVA80
Chews tape intermittently Unit will chew tape, highly intermittently. found the greaseon the shaft of the b gear assembly to be very sticky. it seems as theunit ages the grease thickens and restricts the rotation of the gear onthe shaft.
SONY EVA300
Chews tape intermittently Unit will chew tape, highly intermittently. found the greaseon the shaft of the b gear assembly very sticky. it seems as the unitages this grease thickens and restricts the rotatation of the shaft.
SONY KV32HSR10
Severe pincushion, replaced shorted l-501 Unit had severe pincushion. found l-501 shorted. check dam-per diode for cold solder connections.
SONY TCDD3
Tcd-d3 test mode The test modes in the tcd-d3 service manual are confusing, anddifficult to use. -hq comments: a service bulletin has been created (see s/b 157- testmode clairification) refer to this s/b when using the test modes.
SONY STRD2020
No audio or digital output No audio output and no equalizer display, audio relays turnon.
SONY STRAV1020
Unit in protect mode Unit in protect mode.
SONY EVDT1
Tv hv shutdown when no video line in connected With no line in video input, the tv section of the evdt1 wouldgo into shutdown. only powering down and powering up again would restorethe video. camera in was ok.
SONY CDX7540
Unit will not accept discs I have seen three units with the pll frequency of 4.2, 4.27and 4.22mhz. customer complaint - unit does not accept discs. problemsdid not show on the bench. all other adjustments rf, ef balance, t-gainand f-gain looked good.
SONY KV20TS30
Low band vhf channels have ghosting, see sb tvp0101 Recent installation of new tv in an area near the televisiontransmitting tower. low band vhf channels have considerable ghosting dueto direct pick-up of air signal and cable signal. customer name:mrs. jones, 55 chumesera, san francisco, ca 94132 415/33
SONY KV1380R
Distorted osd Distorted osd so that: instead of multiple small barsappearing in volume up/down mode, one solid variable bar can be observedon the screen.
SONY KV32XBR65
Tuner drifts on low band, replaced tuner Channels 2-6 would drift.
SONY SLV575UC
Eats tapes - won't turn off Customer complaint was that the unit eats tapes and unable toturn unit off.
SONY CDP190
Doesn't play Doesn't play. spindle motor replaced. per servicer, this is the second time this motor was replaced in this unit.
SONY BMC550
Transport stops after rec button is pushed With unit loaded with a blank tape and fresh battery or powersupply, unit will power up. seconds after rec button is pressed unitstops (not emergency shutdown). pressing rec button immediately aftercauses identical symptoms.
SONY TCW300
Wrong part number for ref. no. 155, page 2 of supplement 1 On page 2 of supplement no. 1, reference no. 155 is listed asa shaft, pulley with p/n 3-390-203-01. this is incorrect.
SONY D9
Incorrect part number, ic-802 (ba10339f) The part number in the service manual for ic-802, ba10339fis incorrect. the part number listed is for an fa7616n. -hq comments: the correct part number for the ba10339f is 8-759-982-77.thank-you for bringing this error to our attention. a service bull
SONY TCW190
Wrong part number for ref. no. 155, page 2 of supplement 1 On page 2 of supplement no. 1, reference no. 155 is listed asa shaft, pulley with p/n 3-390-203-01. this is incorrect.