Sony Repair Tips
Search: sony
Results: 20088
Results: 20088
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
DVD DVP-K88P
*** |
Progressivescan activated | Just put the device on stand by and enter the sequence 369 and press stand by for 5 seconds and release. | Or type 369 and press stand by. That's it and you're done. | wagner |
| SONY |
KV28FQ86E
AE6BA |
16 blinks- pip error | Indicator fault is related to the ic6802 mcz3001db replace | Tuga_75 | |
| SONY |
KV 140MG
|
Has sound, no image | Rusty tube socket | c@rlinhoselectro | |
| SONY |
KV 200MG
|
When it starts and cuts off, it does not oscillate, releasing the capacitor connected to the deflector coil, it oscillates but the screen does not light up | Oxidized deflector coil and open 15hms resistor r538 | And the problem was solved | |
| SONY |
DVP-NS575P
|
Sometimes it turns on and sometimes it doesn't turn on | Swap d315,d317 and c316 | ELETRO JACOB | |
| SONY |
KV-2162
|
Black screen with normal sound | 3k3 resistor (on the tube board) screen | Make the replace | jair.com2008 |
| SONY |
KV-M2140E
BE2A |
When turning on, the LED oscillates once and does not start | R801 (1k), q801 (c2688) | JOAQUIM CUNHA | |
| SONY |
FH-B900
|
I'm sound | Gun box relay but tsound is no sound ic901 bad | retec | |
| SONY |
KLV-40S200A
|
No audio | Communication: trident board for audio board. | Flex cable. opens track due to oxidation. | Luna |
| SONY |
21FS140
|
Totally off | Zener diode 5.1v d605 shorted to the power supply | Replace for the same original mtzj-5,1b - I put the 1n751a and it worked too | ROMOLO FILHO |
| SONY |
KV140MG
|
Tube all white when turned on | I changed the vertical outlet and it was normal | celio | |
| SONY |
KVB1
|
Speaks normally, but has no image | 220k resistor and a flay bek pin output | celio | |
| SONY |
KVM2100E
BE2A |
D611(b+ protection zener diode) in c. | B+ high, change d611 and ic601 | jose luis calcada | |
| SONY |
KVM2100E
BE2A |
Hand plucks | Q601 e r615 chip 33r | Replace q601 and r615 | jose luis calcada |
| SONY |
KVM2100E
BE2A |
Don't start | R611 in series with r602 (r602 is below t601) | Replace the two resistors. | jose luis calcada |
| SONY |
KVM2100E
BE2A |
Does not start | Ic601-str54041 | Replace ic601 | jose luis calcada |
| SONY |
KVM2100E
BE2A |
No e/w correction | C806--dry and/or r804 smd open | Replace c806 and r804 | jose luis calcada |
| SONY |
KV140MG
|
Opens the sound, but not the image | Defective transistor | Replaced q711, q731 and q751. problem solved | Cleiton |
| SONY |
HCD-ZUX9
|
Completely stopped | Power outage | This equipment has an ac-dc converter, first check if it has a 4v output to feed the relay coil, if not, replace the converter and if it still doesn't work check if 4v is coming to the cn 201 connector on the side plate If so, the panel LED will light up but nothing will work, then check if 3.3v is coming out through the same CN201 connector, if not, just replace the reset IC or IC 202 | edson102030 |
| TV SONY |
KV 14VM 5 BR
|
TV with image but very low sound. | After changing the c 225, it was shorted. For those who don't have the schematic, this capacitor is on pin 13 of the selector, ok. | jaironuness |