Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDPC40
|
Intermittent operation - skipping, no start or shutdown | Very intermittent operation of unit. problem can manifestitself as skipping during play mode, intermittent shutdown, inability toread disc or intermittent start. problem is caused by a minute particleof matter (in this case a tiny piece or printed circ | ||
| SONY |
CDXR66
|
Audio cuts out intermittently | Audio will cut out - sometimes with time or with temp. | ||
| SONY |
KV1946R
|
Squeal - reduced picture size, replaced l-904 | Unit squealed and displayed unsynchronized picture withreduced height and width. | ||
| SONY |
CFS903
|
Intermittent or no radio | When switching unit to radio, base voltage of q-301 does notreach 4.9 volts - emitter voltage is b+ to radio. if voltage is low,radio may be intermittent or dead if voltage is too low. dvm measurementof q-301 shows good transistor but under load transi | ||
| SONY |
CDXA20
|
Servo noise heard during quiet passages | To improve the signal to noise ratio, the service bulletinnumber aud0152 has an error in it. -hq comments: a revised service bulletin will be issued to correct forthe error. the added jumper was incorrectly shorting ic-503/pins 9 and10. it should shor | ||
| SONY |
KV27TS20
|
No video, replace comb filter cm-301 | Unit displayed no video, but had character displays. hadsound - g2 normal. | ||
| SONY |
VTX1100R
|
No functions - erratic display | At turn on, unit would come up with aux light on and randomnumbers on display. sometimes the display was totally dead. theresponder light would come on when remote used, but no function exceptpower worked. missing key scan pulses on ic-101, but clock | ||
| SONY |
CFSW370
|
Missing part number for spring | Part number missing for wishbone shaped spring on deck(center between spindles). | ||
| SONY |
SRS150
|
Audio | Complaint was no bass in speaker. i changed speaker, thisdid not help. the audio sounded clean but was lacking bass response. inoticed the audio was lower on the input of ic-201 in comparison toic-101. i traced low audio back to voltage amp q-203, al | ||
| SONY |
CFSW350
|
Removal of main pc board | Removal of main pc board from cage. caution: the pc board is held by four plastic clips on the rear case. clips are located by the speaker terminals and power plug. these clips are easy to break. | ||
| SONY |
FD230
|
Will not power on or tune in channel, see sb50 | Unit tuning point which should be at 32v is shorted to groundand burns out dc/dc conv. (ref. no. ic-602 on the a board part number,a-3015-759-a) and 6 volt regulator (q-601 part number, 8-729-101-07) whichis on the same board. received three replacemen | ||
| SONY |
CCDF55
|
Intermittent audio when using acv-60 | Intermittent playback audio when using the acv-60. movingthe cable next to the adaptor that connects to the camera increasedintermittency. | ||
| SONY |
CDXA30
|
Balance ring for cd cause it to jam while loading disc. | Disc will jam if owner has affixed adhesive balance ringaround it's circumference. -hq comments: the balance ring on the outside edge of the disc causeit to catch on the roller, as it's thickness is increased. it can alsoprevent it's slipping onto the | ||
| SONY |
CDXA20
|
Balance ring for cd cause it to jam while loading disc | Disc will jam if owner has afixed adhesive balance ringaround it's circumference. -hq comments: the balance ring on the outside edge of the disc cause itto catch on the roller, as it's thickness is increased. it can alsoprevent it's slipping onto the t | ||
| SONY |
CDXA10
|
Balance rings for cd's cause cd to jam while loading disc | Disc will jam if owner has afixed adhesive balance ring aroundit's circumference. -hq comments: the balance ring on the outside edge of the disc cause itto catch on the roller, as it's thickness is increased. it can alsoprevent it's slipping onto the t | ||
| SONY |
CCDF33
|
Part no ic-503 co2 board | The replacement part is smaller than the original and doesn't fit. | ||
| SONY |
CCDF45
|
Part no - ic503 co-2 board | The replacement part is smaller than the original, and doesn't fit. | ||
| SONY |
CCDTR5
|
Caution light comes on after a few seconds | Take-up reel stops after a few seconds and caution light comeson. | ||
| SONY |
EVCX10
|
Evf cable too short | Evf cable is too short. -to tokyo: when ordering the evf cable part number 1-556-824-61, thereplacement sent is about 4 inches (100mm) long. however, the originalpart is about 7 inches (about 165mm) long, and the replacement is tooshort. can you pleas | ||
| SONY |
CCDTR5
|
Part number for plastic shield | I need the part number for the clear plastic shield on thecassette compartment. -hq comments: the part number for this shield (called the cassettecover) is 3-736-834-01. |