Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDV110
|
No video 5v from dc to dc converter | No video 5v from dc to dc converter. this 5vdc line measuredabout 20Ω to ground. c-208 was shorted. | ||
| SONY |
KV27XBR50
|
Yoke squeal, replace with p/n 1-451-275-41 tvp sb # 114 | Squealing yoke. | ||
| SONY |
STR313
|
Distorted audio on one channel & ic gets hot. | Original 8-759-301-25 replaced by 9-919-580-00. right sideworks with some static. left side is dead. ic gets very hot. it wasreported this replacement had problems in other models. -hq comments: refer to hifi s/b no. 0116. as the si-1125hd has been | ||
| SONY |
SLHF600
|
Playback speed is too fast | This problem may be intermittent. when playback mode isactivated, caused by item 182 u end not catching a plastic pin at thebottom part of t.u. sensor. this pin is subject to wear from normalusage. the sensor does not move to the proper position for t | ||
| SONY |
SPP110
|
Incorrect part number | The service manual part list indicates ic-207 as part number,8-759-205-06 description tc74hc74f. this is incorrect, ic-207 is partnumber, 8-759-205-41 description tc74hc4066f substituted by part number,8-759-239-25 description tc74hc4066af. refer to se | ||
| SONY |
MDP210
|
No operation | Unit would not play laser discs. found all ld adjustmentsoff. aligned and tested unit. discs played correctly but picture had nocolor. | ||
| SONY |
CCDTR5
|
Incorrect part number (ic 503) | Part number should be 8-752-031-01. see page 234 of theservice manual. -hq comments: the correct part number for ic-503 on the vc-60 board is8-752-031-01. | ||
| SONY |
SLV70HF
|
Noisy picture ep mode only | Head output is very low, noisy ep picture. | ||
| SONY |
CFS903
|
Keypad (rubber cover) breaks (tears) easily and prematurely | Sample forwarded for evaluation and pad replaced. a monthlater it had to be replaced again due to breakage. the customer claims noabuse. -hq comments: please reorder the md button packing using the partnumber for the new improved part. the material c | ||
| SONY |
D2
|
Replacement assembly idle gear binds | Replacement assembly idle gear binds. getting several re-calls in service center. i am enclosing sample unit. this unit binds andskips intermittently. motor assembly has been replaced in unit. -hq comments: due to design limitations, cost and part s | ||
| SONY |
KV2681R
|
Ic-301 chip substitution, cx-20129 to cx-20193 | The original ic-301: cx20129, part number 8-752-012-90 wastemporarily not available. tried using cx20193 but picture was rollingvertically. can this chip be used as a substitute? references: seeservice bulletin ctv0236 and 24. -hq comments: when usin | ||
| SONY |
CCDSP7
|
No vtr functions | Found no vtr functions after loading of tape. unit doeseject and works fine in camera mode. unit acts like it is in offposition. | ||
| SONY |
FD500
|
Dead - ic-451 loaded (sound output ic) | Unit arrived dead. found fuse (f-602) blown. checked andfound ic-451 with a chipped-off body. found this problem very common forfd-500. this unit had previous problem of a blown ic-451. prematurefailure of ic-451 and f-602 is too high. | ||
| SONY |
DT2
|
Production change in spindle motor assembly | I have noticed that newer models have new motor assemblies(x-264-153-72) installed from manufacturer. they also have a new md cover(ref. no. 73) with a different finish. do models with new md covers allhave new motor assemblies? or do you have a list | ||
| SONY |
DT4
|
Production change in spindle motor assembly | I have noticed that newer models have new motor assemblies(x-264-153-72) installed from manufacturer. they also have a new md cover(ref. no. 73) with a different finish. do models with new md covers allhave new motor assemblies? or do you have a list | ||
| SONY |
D4
|
Production change in sled motor assembly | I have noticed that newer models have new motor assemblies(x-264-153-72) installed from manufacturer. they also have a new mdcover (ref. no. 73) with a different finish. do models with new md coversall have new motor assemblies? or do you have a list | ||
| SONY |
D2
|
Production change in spindle motor assembly | I have noticed that newer models have new motor assemblies(x-264-153-72) installed from manufacturer. they also have a new md cover(ref. no. 73) with a different finish. do models with new md covers allhave new motor assemblies? or do you have a list | ||
| SONY |
CCDF45
|
No part number for frame | I need the part number for the frame to which the lens andmechanism are attached. it is shown on page 175 next to item no. 115.it is labeled not supplied. when i received a unit for repair, whichwas dropped, this part is usually damaged. there are man | ||
| SONY |
CDPC100
|
Disc spins backwards | Disc would spin backwards. reversed motor leads and unitwould play ok until ic-202 warmed up then spindle motor would again runbackwards. | ||
| SONY |
D9
|
No disc rotation | Spindle motor would not operate. |