Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDPC9ESD
|
No part number - clips for plastic bushings for worm gears | There is no part number listed in the service manual for theclips which hold the plastic pieces which ride on the worm gears of theelevator assembly. -hq comments: the part number for the clips is 4-926-216-00. | ||
| SONY |
CDPC900
|
No part number - clips for plastic bushings for worm gears | There is no part number listed in the service manual for theclips which hold the plastic pieces which ride on the worm gears of theelevator assembly -hq comments: the part number for the clips is 4-926-216-00. | ||
| SONY |
SPP60
|
Part number incorrect - top cabinet, base unit | The part number for the top cabinet for the base unit iseither incorrect, or has not been registered in rpc. -hq comments: to tokyo: is the part number listed correct for the topcabinet? if not, please inform us of the correct part number. if thepart | ||
| SONY |
STRAV850
|
No display in lower left corner of display | The volume indicator, balance indicator, tremble and bassindicator would not light. however, the subsonic indicator and spectrumdisplays worked. | ||
| SONY |
KV20TS30
|
Rabbit antenna, 1-501-372-41 see flash 43 | Rabbit antenna is not listed in the service manual. -hq comments: rabbit antenna is not supplied as accessory for this setit can be ordered separately by part number 1-501-372-41please refer to flash # 43 for recommend antennas for various t.v.. | ||
| SONY |
CPD1302
|
Hi v shut down when computer turned on. | Unit would shut down whenever computer connected to it wasturned on. worked o.k. after powering monitor down and up again. | ||
| SONY |
DT3
|
Intermittently skips or shuts off only bp-3 batt. operation | This unit works properly by ac930 but it skips or shuts offintermittently using bp-3. b+ (4.6v) is unstable. | ||
| SONY |
CCDF40
|
41 pin flex connector part number | Need part number for the 41 pin flexible cable between the(ss-86) board and the (va-40) board. -hq comments: the part number is 1-626-229-11. | ||
| SONY |
KV27XBR15
|
Safety related adjustment, refer to tvp sb # 62r2 | Per the attached (safety related adjustment) page from theservice manual, we are required to use a regulated power supply adjustablebetween at least, 140 to 145 vdc. such a supply is not on the ssc re-quired test equipment list nor have i ever encounter | ||
| SONY |
CCDF70
|
No af, zoom or title function | Unit had no autofocus, no zoom operation, no title functionand there was a flashing of light in the evf even when unit was turnedoff. ic-200 on (ss-93) board had no clock. | ||
| SONY |
CDP670
|
Pause mode with 9 or more programmed selections | When 9 or more selections are programmed, and drawer is openedand closed before pushing play, unit goes into pause after playing lastselection. with 8 or less selections, or with 9 or more without openingand closing drawer before pushing play, unit goes | ||
| SONY |
CDXR77
|
Main board layout for ic-103 is shown turned 90 degrees | The board layout for ic-103 on the main board is shown turned90 degrees. it is very easy looking at the board layout to replace thewrong ic. -hq comments: the silk screening on the board for ic-301 is off by 90degrees. tokyo will correct production fo | ||
| SONY |
NTM1
|
Frequency settings on ntm-1 | How many receiver frequency settings are there in nusserymonitor ntm-1? what is the frequency? -hq comments: there are two frequency settings for the ntm-1.switch - a: 49.845 mhzswitch - b: 49.875 mhz | ||
| SONY |
TAE1000ESD
|
Cannot monitor while effect recording on ta-e1000esd | If effect recording using tape 2 output and monitoring thepower supply, an oscillation is heard. this only happens when effect recordingrecording non-processed signal works fine. -hq comments: this is normal operation for this unit. it is designedthe same a | ||
| SONY |
MPKV11
|
V99 does not go in straight | Customer claims that the ccdv99 fits in the mpkv11/1, but doesnot line up perfectly with the wide angle lens in the mpk unit that ismounted to the camera holder. -hq comments: we believe that the customer is using the mounting for theccd-v11 not the ccd | ||
| SONY |
KV32CX10
|
Jagged vertical lines, resolder c-685 "g" board | Vertical lines in the picture were jagged. | ||
| SONY |
CCDF50
|
No function | Report that two units had no function. | ||
| SONY |
SLV70HF
|
Does synchro edit also act as an edit switch? | Does the synchro edit button, in addition to providing thesynchro edit, also function as an edit switch and flatten out the videofrequency response? -hq comments: no, it does not act as an edit switch. | ||
| SONY |
PSLX295
|
Dust cover for pslx295 | There is no part number for a dust cover for this model.since it is part of a system, no dust cover provided. | ||
| SONY |
CCDV11
|
Cassette ejects, but new cassette cannot be inserted | The cassette will eject properly, however, the loading motordoes not reverse the small amount needed to put the mechanism back in theloading/unloading mode after eject. found cassette lock switch permanent-ly closed. after replacement, the same problem |