Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
SL5000
|
Replacement capstan motor does not fit | The original part number a-6737-103-a, which subs to 154149011as a replacement part, does not fit according to the servicer. he saysthe shaft is too short. do you have any problems with this part? -hq comments: no. this has been the replacement part | ||
| SONY |
CCDF35
|
Iris opens and closes continually | Under normal lighting conditions, iris opens and closesuncontrollably at a rapid rate. this does not occur under low lightconditions. videotape of symptom included. -hq comments: it appears the iris or iris drive is defective. | ||
| SONY |
CCDTR5
|
Tapes jamming | Tape jammed in the unit. inspection revealed tgi to be out ofthe groove on tgi cam base (301 ref.). by placing the tgi arm assemblypin back in the groove on tgi cam base, unit worked o.k. this servicerhad two units in for repair with the same problem. | ||
| SONY |
CCDV99
|
Angle of view | What are the wide and telephoto angles of view for the ccdv99? | ||
| SONY |
KV1929R
|
Cb interference, see sb ctv288r | Cb interference heard from the speaker, even when the set isoff. -hq comments: please refer to service bulletin no. ctv288r. | ||
| SONY |
KV1997R
|
Cb interference | Cb interference heard from the speaker, even when the set isoff. -hq comments: please refer to service bulletin no. ctv288r. | ||
| SONY |
KV1926R
|
Cb interference, see sb ctv288r | Cb interference heard from the speaker, even when the set isoff. -hq comments: please refer to service bulletin no. ctv288r. | ||
| SONY |
CDPC9ESD
|
No part number - clips for plastic bushings for worm gears | There is no part number listed in the service manual for theclips which hold the plastic pieces which ride on the worm gears of theelevator assembly. -hq comments: the part number for the clips is 4-926-216-00. | ||
| SONY |
CDPC900
|
No part number - clips for plastic bushings for worm gears | There is no part number listed in the service manual for theclips which hold the plastic pieces which ride on the worm gears of theelevator assembly -hq comments: the part number for the clips is 4-926-216-00. | ||
| SONY |
SPP60
|
Part number incorrect - top cabinet, base unit | The part number for the top cabinet for the base unit iseither incorrect, or has not been registered in rpc. -hq comments: to tokyo: is the part number listed correct for the topcabinet? if not, please inform us of the correct part number. if thepart | ||
| SONY |
STRAV850
|
No display in lower left corner of display | The volume indicator, balance indicator, tremble and bassindicator would not light. however, the subsonic indicator and spectrumdisplays worked. | ||
| SONY |
KV20TS30
|
Rabbit antenna, 1-501-372-41 see flash 43 | Rabbit antenna is not listed in the service manual. -hq comments: rabbit antenna is not supplied as accessory for this setit can be ordered separately by part number 1-501-372-41please refer to flash # 43 for recommend antennas for various t.v.. | ||
| SONY |
CPD1302
|
Hi v shut down when computer turned on. | Unit would shut down whenever computer connected to it wasturned on. worked o.k. after powering monitor down and up again. | ||
| SONY |
DT3
|
Intermittently skips or shuts off only bp-3 batt. operation | This unit works properly by ac930 but it skips or shuts offintermittently using bp-3. b+ (4.6v) is unstable. | ||
| SONY |
CCDF40
|
41 pin flex connector part number | Need part number for the 41 pin flexible cable between the(ss-86) board and the (va-40) board. -hq comments: the part number is 1-626-229-11. | ||
| SONY |
KV27XBR15
|
Safety related adjustment, refer to tvp sb # 62r2 | Per the attached (safety related adjustment) page from theservice manual, we are required to use a regulated power supply adjustablebetween at least, 140 to 145 vdc. such a supply is not on the ssc re-quired test equipment list nor have i ever encounter | ||
| SONY |
CCDF70
|
No af, zoom or title function | Unit had no autofocus, no zoom operation, no title functionand there was a flashing of light in the evf even when unit was turnedoff. ic-200 on (ss-93) board had no clock. | ||
| SONY |
CDP670
|
Pause mode with 9 or more programmed selections | When 9 or more selections are programmed, and drawer is openedand closed before pushing play, unit goes into pause after playing lastselection. with 8 or less selections, or with 9 or more without openingand closing drawer before pushing play, unit goes | ||
| SONY |
CDXR77
|
Main board layout for ic-103 is shown turned 90 degrees | The board layout for ic-103 on the main board is shown turned90 degrees. it is very easy looking at the board layout to replace thewrong ic. -hq comments: the silk screening on the board for ic-301 is off by 90degrees. tokyo will correct production fo | ||
| SONY |
NTM1
|
Frequency settings on ntm-1 | How many receiver frequency settings are there in nusserymonitor ntm-1? what is the frequency? -hq comments: there are two frequency settings for the ntm-1.switch - a: 49.845 mhzswitch - b: 49.875 mhz |