☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY TAE1000ESD
Cannot monitor while effect recording on ta-e1000esd If effect recording using tape 2 output and monitoring thepower supply, an oscillation is heard. this only happens when effect recordingrecording non-processed signal works fine. -hq comments: this is normal operation for this unit. it is designedthe same a
SONY MPKV11
V99 does not go in straight Customer claims that the ccdv99 fits in the mpkv11/1, but doesnot line up perfectly with the wide angle lens in the mpk unit that ismounted to the camera holder. -hq comments: we believe that the customer is using the mounting for theccd-v11 not the ccd
SONY KV32CX10
Jagged vertical lines, resolder c-685 "g" board Vertical lines in the picture were jagged.
SONY CCDF50
No function Report that two units had no function.
SONY SLV70HF
Does synchro edit also act as an edit switch? Does the synchro edit button, in addition to providing thesynchro edit, also function as an edit switch and flatten out the videofrequency response? -hq comments: no, it does not act as an edit switch.
SONY PSLX295
Dust cover for pslx295 There is no part number for a dust cover for this model.since it is part of a system, no dust cover provided.
SONY CCDV11
Cassette ejects, but new cassette cannot be inserted The cassette will eject properly, however, the loading motordoes not reverse the small amount needed to put the mechanism back in theloading/unloading mode after eject. found cassette lock switch permanent-ly closed. after replacement, the same problem
SONY SLV555UC
Ics on the power block Currently ic-201, ic-202, ic-203 and ic-204 of the powerblock are unavailable from kcp. also, part numbers have not beenassigned to them. -hq comments: the part numbers of the ics are asfollows:ic201 - 180879611ic202 - 180879511ic203 - 180802211ic204 -
SONY SLV353UC
Ics on the power block Currently ic-201, ic-202, ic-203 and ic-204 of the powerblock are unavailable from kcp. also, part numbers have not beenassigned to them. -hq comments: the part numbers of the ics are:ic201 - 180879611ic202 - 180879511ic203 - 180802211ic204 - 874992043
SONY SLV757UC
Head gap size What is the head gap size of the slv-757?
SONY SLV353UC
Head gap size What is the head gap size of the slv-353?
SONY CDXA30
Skipping in cold weather. A dealer reported that he has two complaints of these unitsskipping when the temperature is under 25 degrees. units ok after carand unit operates for a while, or temperature warms up. have you heardof this? -hq comments: the cold weather skipping is d
SONY CCDF35
Plastic mold on chassis broken. A molded piece of plastic that goes into the cassette to holdit firmly was broken. the machine worked o.k., except for rewind tapewould get chewed on top. reason is, this plastic was broken, and thetape is not held firmly to the chassis.
SONY MDP510
Crosstalks appears with ld, cd spins but shuts off When i play ld disk, cross talks appears. when i play cddisk, it spins two or three times, but it shuts off. rf signal distorted.
SONY CDPC50
Motor assembly spindle The spindle motor is mounted in reverse polarity.
SONY SPP50
No communication between base and handset Handset works with b & k 1050 analyzer, but would notcommunicate with base.
SONY SPPS10
Buzzing noise from base unit I have seen this problem on several units - after the baseunit gets hot, you hear a loud buzzing sound.
SONY KPR4110
Poor convergence, replaced r-6111, 6112, and 6114 After changing defective stk ic on d pcb convergence, stillwould not function normally.
SONY CCDTR5
No functions, caution light blinks Unit powers up, but no functions. tries to eject, andcaution light blinks.
SONY CCDSP7
Lines in playback Herring bone in playback after a couple of minutes. problemis present if self-recorded or pre-recorded tape used.