Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
ITK500
|
Could not break dial tone while dialing | Could not break dial tone when dialing. did not find anyvoltage at pin 15, ic-201. c-212 was shorted. | ||
| SONY |
ITK500
|
No speaker phone or radio audio | No speaker phone or radio audio. i did not find any b+ atpin 26, ic-1. c-25 was shorted. | ||
| SONY |
KPR36XBR
|
Intermittent problems on the (a) board, liquid from crt | This unit has had intermittent problems occuring in thecircuitry of the (a) board. the most recent failure was in the displaycircuit. l-101 on pins 1 and 2 of ic-104 was open. at this time, wenoticed excessive liquid material on the pc board. this wa | ||
| SONY |
SSM910
|
Dead | F-102 blown. also pertains to serial number 112979. | ||
| SONY |
CDXA20
|
3 inch cd adaptor | Magazine stuck in the unit. when you open unit, find two 3inch cds separated from the adaptor. all are jammed inside the elevator.the 3 inch cd adaptor brand is (recoton). | ||
| SONY |
CFSW50
|
(md) board | The (md) board in this unit does not correspond to theschematic. do we have any additional information? if so, please fax tothe minneapolis ssc. -hq comments: we have no additional information on this at this time,and we have not had any other complai | ||
| SONY |
CDPC5F
|
Cables | I need the 7 conductor cable that connects cnp504 and the 4conductor cable that connects cnp505. if the cables are not available,can you supply the part number of soft flexible ribbon cable. i.e.neoprene insulator? thank you. -hq comments: these cabl | ||
| SONY |
KV1923
|
Intermittent tuning operation | The unit would intermittently not tune or accept tuningcommands. all the control ics of course were changed. the problem wascaused by a very intermittent l035 coil. it would increase resistance toabout 1000Ω. replacement resolved the problem. -h | ||
| SONY |
CPD1201
|
Miswired board | Picture took too long to come up. | ||
| SONY |
KV2680R
|
Focus spark gap arcing, replace crt socket | Crt was replaced. now arcing from focus spark gap (neon lampwithin crt socket) occurs every 5 seconds continuously, causing randomhorizontal lines through picture, but no shrinking of picture size. | ||
| SONY |
KV2737R
|
Part number needed for cp-104, use other part | No part number for capacitor pack cp-104 on the (a) board. | ||
| SONY |
KPR36XBR
|
Part number for cp-500 diode pack, 8-719-109-93 diode p/n | What is the part number for cp-500 ? -hq comments: cp-500 consists of three zeners: rd6.2e-n2 part number 8-719-109-93. you must cut out the defective diode and replace it with a new diode. | ||
| SONY |
WMF59
|
Incorrect part lever ff | Replacement ff lever is different from original. -hq comments: stock at kcp was temporarily mixed. the stock is beingrectified. please order again. | ||
| SONY |
KV27HFR
|
No power on via remote control; power off is ok, open foil | Once set manually powered on, all other remote and manualfunctions ok. remote control works ok on another set. | ||
| SONY |
FDL330S
|
The picture flickers after 20 minutes | The picture flickers after a short time. | ||
| SONY |
TCWR500
|
Missing part number and part number not in computer | 1. display board and translation board does not have a partnumber in the service manual (see page 6).2. part number a2105028a, reference no. 1, supplement 1 is not loaded inthe computer. -hq comments: the display and translation boards are included with | ||
| SONY |
XR7180
|
Missing part number | There is no part number for this part in the manual, also nomention of it in the replacement book. -hq comments: the part number is not missing. it is listed in theservice manual on page 44. however, the part number is incorrect. thecorrect number is | ||
| SONY |
ITA650
|
High-pitch noise when using transfer mode | Unit disconnected after 4-5 seconds during recording of theicm. followed service bulletin tel-002. after this, recording icm ok.another problem came up. when using the transfer mode to playback icm, ahigh-pitch noise came out. | ||
| SONY |
FD270
|
Part number for stand on back of fd270 | Need the part number for stand on back cabinet of fd-270. -hq comments: thank you for your report. stand is part of rearcabinet. part number is in service manual according to color of cabinet. | ||
| SONY |
FD270
|
A board not compatible, see sm supplement | New board layout different - 3 wire lead from board neartuner. ic-201 is different chip. -hq comments: thank you for your report. service manual supplement hasissued. |