Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
GV8
|
No power | Unit had no power. pin 34 of ic-101 servo/system control icwas dead. found x-101 defective. | ||
| SONY |
EVS800
|
Loading | Loads tape then right away unloads. does not thread tape. | ||
| SONY |
XR7150
|
May not turn on or select various functions such as am or fm | May not turn on or select various functions such as am or fmetc. also applies to serial number 30058. the two units listed are onlyrepresentative of a number of similar failures. | ||
| SONY |
STRAV340
|
At maximum volume - sound hardly audible | Servicer called me to explain that at full volume you canhardly hear audio o/p. he stated that asp chip ic-601 had been replacedwith some results. he said he had all voltages as well as data clk andstrobe, but very little output from ic-601. | ||
| SONY |
TCWR800
|
Cannot do tape speed adjustment as per manual | Cannot do tape speed adjustment as per manual. | ||
| SONY |
TCW600
|
Cannot do tape speed adjustment as per manual | Cannot do tape speed adjustment as per manual. | ||
| SONY |
TCW9ES
|
Cannot do tape speed adjustment as per manual | Cannot do tape speed adjustment as per manual. | ||
| SONY |
CDXA20
|
White noise on soft passages or between songs | A customer took his unit and this article to his dealer withthe same complaint. what is the fix? reference car audio andelectronics. -hq comments: service bulletin car stereo no. 135 has been written toremedy this situation. i will fax you a copy. | ||
| SONY |
TCW7ES
|
Cannot do tape speed adjustment as per manual | Cannot do tape speed adjustment as per manual. | ||
| SONY |
XE8
|
Wrong part number | Reference numbers 901 and 905 have the part numbers reversed.reference number 901 is part number a-3270-404-a nad is the digital board.reference number 905 is part number a-3270-407-a and is the audio board onpage 17 of the xe-8 manual. -hq comments: ch | ||
| SONY |
CDPC30
|
Pivot breakage | Left side pivot supporting optical assembly are breaking dur-ing shipment of units if subject to rough handling and transit key not inplace. the pivot is an integral part of the main frame. | ||
| SONY |
CPD1302
|
Set dead or intermittently so | Set is dead or intermittently so. plus lead of c-549 comesloose from its soldered position on the board. this is caused by pressurefrom the bc connector board edge which is against the capacitor. so muchpressure and friction exists that the plastic sl | ||
| SONY |
CCDV220
|
Excessive dropouts | Unit is experiencing excessive dropouts. | ||
| SONY |
KV20TX10
|
Dead unit, replace ic-101, q-121 & d-605 | Set is dead would not turn on. replacing ic-101 on (a) boardrestored operation. now no volume control. q-121 e.b. junction open.q-121 is volume control transistor on (a) board. vcc up to about 8 volts. | ||
| SONY |
KPR36XBR
|
Diode d-17 shorts, change l8 to p/n 1-408-300-00 | After replacing (d-17), gu3 diode shorts out immediately. | ||
| SONY |
CCDV11
|
Alignment procedure for camera section | When trying to perform alignment procedure on camera sectioniris - white balance etc., rm-94 readout was confusing according to themanual. data and address locations did not make sense. | ||
| SONY |
KV20TS10
|
Verti8cal fold over and retrace lines, leaky c-534 | Unit displayed about two inches of foldover with retracelines. | ||
| SONY |
SPP100
|
Intermittently will not find channel | Unit will not lock on channel intermittently and at othertimes is slow. is it possible to modify, so it stays on one (1) channel? -hq comments: if the unit does not lock on a channel, it is due to ex-ternal interference (rf) being present. due to soft | ||
| SONY |
KV1393R
|
Wrong part number for esif diode | Part number for (d-513) esif is wrong. | ||
| SONY |
KV1392R
|
Wrong part number for esif diode, 8-719-300-65 | Part number for (d-513) esif is wrong. |