Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SONY |
GV8
|
Vertical red line at side portion of the screen | There is a vertical red line at the side portion of thescreen. | ||
SONY |
TAF444ES
|
Burnt volume control and board | Board burnt beyond repair - volume control burnt. no partnumber for stuffed board. no replacement units in stock. we require helpin completing this repair (asap) as customer is very concerned and gettingangry. -hq comments: tokyo has the empty board | ||
SONY |
SPPS10
|
No talk mode | Base unit would not receive signal from handset. foundreceive section operating normally on both channels but unit would notcome on. (in use) led stayed off. | ||
SONY |
CDP707ESD
|
Does not read disc | Unit will not read disc. after loading, the disc will spinforward for a second then spins backwards and shuts down-then (disc memo)appears on the display. | ||
SONY |
ICF2010
|
Improving sensitivity using rod antenna | On some units that have been in service for a while the custo-mers complain of poor sensitivity using the rod antenna. external rf in-put is ok. the problem may be caused by two factors. 1. the rf board be-gins to sag and does not permit the antenna c | ||
SONY |
SPP80
|
Static noise in battery save mode | Unit makes static noise from handset speaker during batterysave mode only. there is no noise in normal mode. this is the fifth uniti have seen with this problem. | ||
SONY |
SPPS10
|
Handset power locked on, no functions | Received several units that would not go into battery save(standby) mode. removing battery would not reset the unit. when batteryis reinstalled, the battery led comes back on. the handset will notfunction in any way at all. also pertains to serial nu | ||
SONY |
SLV50
|
Bad pinch roller | Pinch roller forces capstan motor down during operation. | ||
SONY |
CCDF40
|
No audio in rec | No audio in rec. found c-560 off of the agc circuit to beleaky. | ||
SONY |
CDPC10
|
Unit jams after repair | Unit jammed after a minor repair - erratic operation would notplay disc. totally unrelated to original problem. | ||
SONY |
STRAV500
|
Missing bottom plate part number | The bottom plate part number is missing in the service manual. | ||
SONY |
TCW190
|
Missing part number | Part number for the motor is missing in the service manual. | ||
SONY |
TAAX435
|
Malfunctioning function select button | When pressing function buttons, leds will light and then goout. no audio switching. | ||
SONY |
TCWR700
|
Adjustment of speed | Replaced motor in a deck. needed to set normal and highspeeds. manual instructs you to short cn-811 pin but there are two. | ||
SONY |
XR7000
|
Dead unit | No b+ to radio tape switch (s-902). | ||
SONY |
XVT600
|
Part number for complete scanner | Customer wanted to purchase the complete scanner for the abovemodel. it is currently not available as a complete unit. | ||
SONY |
SPP50
|
No function | Base unit will not work - push intercom (page) and the unitwill not transmit to the handset. no talk mode on handset. in use leddoes not come on. | ||
SONY |
SPPS10
|
No function | Base unit will not work - push intercom (page) and the unitwill not transmit to the handset. no talk mode on handset. in use leddoes not come on. | ||
SONY |
CDXA20
|
Modified md sled chassis assembly | Chuck plate included with chassis assembly does not fit withcdx-a20 unit. original chuck plate does not work with new chassis. needchuck plate. -hq comments: when the chassis assembly is replaced from the old to thenew type the chuck plate must also b | ||
SONY |
STRAV650
|
Dead set | Unit would not respond to system on switch, pins 18-29 wereall high. data could not be entered from key matrix. changed ic-301 unitstill would not come on. note all i/o data and clock lines were activefrom all three micros. |