Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDV5
|
Clogged heads | Distorted picture. | ||
| SONY |
STRAV780
|
No stereo reception, searches but does not find stations | 1) manual tuning worked ok except for no stereo indicator.2) when performing search, indicator moved on spectrum display screen, butno station markers were placed on it. | ||
| SONY |
KV2075R
|
Weak sound, replace q1404 | Audio is weak on full volume. | ||
| SONY |
SLHF1000
|
Tape path | Customer had bought 2 identical machines. could not playtape recorded on machine #1 or machine #2 and vice versa. picture wouldbreak-up. | ||
| SONY |
DT3
|
The turntable does not spin | 8.6v appear at the collector of q401 when only 4.5v should bepresent. q401 is found to be shorted. many dt-3 or d3 units have thesame problem. | ||
| SONY |
SL2000
|
Substitute pinch roller | When this new substitute part pinch roller x-3669-307-6 isinstalled, the adjustment of the pinch closing limitter (step 3-11 page3-11) cannot be made to fall within the spec. this will cause a veryintermittent jamming of the pinch roller. | ||
| SONY |
SLHF900
|
P/n for circuit board holder is missing | Part number for circuit board holder is missing from manual(see attached). a similar part used in the sl-hf1000 is listed in thes/m. -hq comments: the board holder is unavailable. however, we havereceived a few sample from tokyo. | ||
| SONY |
BMC550
|
Part number omission | Part number for drum base assy is missing from service manual.found that the same part is used in bmc-1000. the part number for thedrum base assy is x-3690-109-1. | ||
| SONY |
KV1975R
|
Intermittent no picture and no sound, c133 shorted | This unit had an intermittent no picture, no sound, no rasterand no function control problem. c133 was found to be shorting inter-mittently. | ||
| SONY |
BMC110
|
Part number for arm plate | P/n for lever ass'y is needed. on page 100 of the s/m, thelever arm does not have a part number. the piece or shield is locateddirectly behind item 270. the bmc-550 and 660 do show a part number. -hq comments: as per s/b #264, part number is 3-681-64 | ||
| SONY |
CDPC10
|
Defective optical block | Won't play. | ||
| SONY |
CDP310
|
Disc will not play | Disc will not play and will scrape on inside of unit. foundroller guide on chucking arm had fallen off. this was a replacement unitwas like this new out of box. -hq comments: too early for a complete stock check. we will contactother regions for addi | ||
| SONY |
CDP510
|
Spindle assy slips down | Caused disc's to be damaged. found spindle assy had slippeddown motor shaft. this was a new unit that failed out of the box. -hq comments: confirm to monitor this and similar models. we willhave stock checked when we can confirm enough additional cas | ||
| SONY |
KV27HFR
|
Dead, replace c-893 and ac fuse | Set dead. | ||
| SONY |
KV2782R
|
Dead/shutdown, replace q-653 | Initially set was dead. would not trigger relay at power on.ic651 corrected first problem. second problem was intermittent shutdowndue to voltage rising at ovp detector pin 2 ic651 (gb board). | ||
| SONY |
KPRM360
|
No picture | No picture. | ||
| SONY |
CDP910
|
Chucking arm ass'y, driver for locking screw | Chucking arm ass'y out of alignment due to nylon roller guidemissing from ass'y. part had fallen out of unit when disc tray opened.head on locking screw driver broke off. sheared off at tip while securinglocking screw. | ||
| SONY |
GENERAL
|
P/n for small lengths of head wire | Customer orders 9-919-566-00 which is 30m of head wire forwm-10. only needs small piece to fix. | ||
| SONY |
SLHF900
|
Reel sensors - s/b #300 and #301 | The service bulletins #300 and #301 refer to new gp2s09bdiodes (p/n 8-719-939-11) being available and new rs boards for 8mmproducts being available. these bulletins also say that the new sensorscannot be mounted on the old boards. please explain how th | ||
| SONY |
TC630
|
Replacement power switch | Ordered replacement power switch p/n 1-514-325-11 whichsubs to 1-516-037-xx. the mounting bracket on the original is 2 1/4long and on the replacement only 1 5/8 long. -hq comments: the original switch is no longer available from kcp.i am afraid you wil |