Sony Repair Tips
Search: sony
Results: 20072
Results: 20072
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDV8
|
Playback jitter and noise | Cleaned, no help. | ||
| SONY |
CCDV8
|
Pins bent on 24 pin connector | Pins 23 and 24 were bent. -hq comments: pins 23 and 24 are not used on the multipin connector.the recommended solution if pins 23 and 24 are bent is to cut them off atthe base. | ||
| SONY |
CCDV8
|
Intermittent no function | Osc change frequency. | ||
| SONY |
CCDV8
|
No eject | Frozen motor. | ||
| SONY |
XR66
|
Non manual autoreverse | Unit will auto reverse at the end of the tape but not whenthe front panel buttons are pushed. | ||
| SONY |
CCDV8
|
Playback picture unstable after 1 - 2 hours | After approx. 1 to 2 hours of operation drum and capstanservos would become erratic. picture would jump from side to side andtracking noise would appear. also, capstan would not run at all. inter-mittent capstan (from play or rec mode) would cause shu | ||
| SONY |
SL2500
|
Rewind problem | Close inspection of enclosed upper drum revealed a slightimperfection (marked). replaced again ok.-hq comments: we will evaluate this sample and inform you of our results. | ||
| SONY |
D5
|
Static after 10 to 30 mins | Unit has static after warm-up. | ||
| SONY |
CCDV8
|
No eject | Unit came in with tape jammed inside. i found that the unitwould not unthread, it would play fastforward and rewind. | ||
| SONY |
CCDV8
|
Shut down after 5 seconds | This particular unit was going into shutdown. after 5 secondsof play, the unit performed all function for that 5 seconds. the onlytime the unit worked without shutting down was on still. | ||
| SONY |
BMC550
|
Noise in audio on quiet scenes | Customer complains about background noise from auto focus andmechanism. cs-5 board changed. -hq comments: due to the proximity of the microphone to the focus andzoom motors, acertain amount of noise is unavoidable during quiet scenes.reducing the gain | ||
| SONY |
CDP102
|
Wrong motor coil wiring | Motor coil wiring is wrong for l152-2 on hook up/board layoutpages. this coil is shown connected out of phase. copy of page 40/41 ofcdp-102 manual attached. note corrected copy. -hq comments: confirmed the wiring of l152-2 should be crossed as youfou | ||
| SONY |
SL2700
|
Cross talk | This unit had bad cross talk on both channels. the outputsfrom the band pass filters was not clean. bpf-801/802/901/902 wereall bad. | ||
| SONY |
CDP200
|
Drawer will not open | The drawer would not open because the chucking motor (m802)gear penetration was too tight. | ||
| SONY |
XO5
|
Low torque | This unit had low take-up torque and would not rewind or ffto the end of the tape. | ||
| SONY |
KV1370R
|
No audio, replaced the if block | This unit had no audio. | ||
| SONY |
SL2710
|
Eject | Pressed eject, unit unload half way, stop and reload. | ||
| SONY |
SLHF300
|
Poor tape path | This one had poor tape path causing improper tracking. i haveseen an increasing number of new units with poor tape path right out ofthe box. | ||
| SONY |
SLHF900
|
No display | No display at all. pin 1 of nd101 not soldered at all. | ||
| SONY |
CDP102
|
Parts rattling around inside | This is the second unit to arrive with parts rattling aroundinside. apparently the screw (ref. 301) that holds pole (a) (ref. 302)and spring (ref. 304) comes loose in transit. both times it has been thescrew toward the rear of the transport. |