Sony Repair Tips
Search: sony
Results: 20072
Results: 20072
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
RS30
|
No ogm recording | The unit did not record ogm and the 1khz beep was always on. | ||
| SONY |
CDP200
|
Top jumps all over the disc | After one hour of playing, the unit started skipping and thetop jumped all over the disc and finally went to the outside.observed the tracking error waveform. it was jumping like crazy. | ||
| SONY |
CDP101
|
Focus coil oscillates | After one hour of playing, the unit started to skip the discand rejected it. the objective lens was making the cracking noise. | ||
| SONY |
TC152SD
|
No ff/rew | The unit did not rewind or fast-forward. | ||
| SONY |
CDP111
|
Noise in audio | There was noise in audio. it sounded like there are a lot ofdropouts on the disc. | ||
| SONY |
ICF4910
|
Sw does not stay on | Am and fm work fine, but the sw mode does not stay on. whenpressing the sw button, the function seems to switch to sw but it doesnot stay in sw. | ||
| SONY |
KV25XBR
|
Missing part # | Please obtain part number for chassis plastic frame andshield sections. -hq comments: the part numbers you need are as follows:ac supply case (main) 4-374-138-02ac supply case (top) 4-374-133-01ac supply case (bottom) 4-374-134 | ||
| SONY |
CDX5
|
No part number - roller pin | Pin dropped out. -hq comments: the part number is a-3239-289-a. the roller assy includesit. we have already issued a s/b (car stereo #47). | ||
| SONY |
KV2657R
|
No pix | Same dealer had 3 sets out of box with no raster. sets hadsound and h.v. they found a crack on all 3 boards in the same spot. | ||
| SONY |
TCD5-M
|
Stock defective plain bearing assy | Servicer reported and showed me 3 plain bearing assy he hadreceived from kc that were defective. when put in tc-d5 unit would runfast. in each case he found fine wire broken. states that he never hadthis problem with others until kc started loose pack | ||
| SONY |
STRAV560
|
No audio output | No sound output. display and all tuning functions workedwithout error. audio signal was at the input of ic602 asp chip but nosignal was being switched out. found pin 21 clock signal being held at4.8vdc. traced this voltage back to main board to q221. | ||
| SONY |
KV1943R
|
Blanking - vert problems, replaced c529 | Set was stretched on bottom three inches of screen. the topfour inches were fine but there was a black vertical bar that was aboutone inch wide on the left and widened to three inches on the right side.it was blacked out in this one area only. adjustin | ||
| SONY |
MLV1100
|
Service manual correction | No audio output. i found out that the s/m and the unit aretotally different. for example, on the s/m audio output ic has 14 pinsbut looking at it i can have only 12 pins. | ||
| SONY |
STRVX4
|
Missing part number - c803 | I need the part numbers for the filter caps designated c803,c804 in the service manual. see page 35 section q4. they filter thebridge diodes output. i have a unit s/n 860295 which had both capacitorsexhibit leakage on the main power board. sample inc | ||
| SONY |
KV1554R
|
Smoking r613 | As soon as master power switch s901 was turned on, r613 wouldsmoke. tv also would not start up when power switch s001 was pushed.bridging ry601 contacts stopped resistor from smoking, and set appearedto work normally. | ||
| SONY |
XRM10
|
Errors in mounting diagrams of service manual | Page 17 (former type) and page 29 (new type) have numerouswire label errors and wiring errors. i noticed these when recently i hadto reconstruct a burned out wire bundle. see attached sheet. note thatcnj321 (i have labeled it for its jack color) can b | ||
| SONY |
KV1916
|
Board showing wrong direction for a diode | Set came in damaged by lightening. audio circuit was wipedout so servicer replaced all components in audio circuit. after finishingvolume was wide open and would not turn down. | ||
| SONY |
KV25XBR
|
No sound, replaced ic103 | No sound when in the tv mode, found no switching (high, low)on ic103, pins 36 and 37. | ||
| SONY |
KV2657R
|
Vertical rolling | After set warms up (approx. 1 to 2 hours), set would havevertical problems, rolling and eventually vertical collapse. | ||
| SONY |
BMC220
|
Tension regulator arm p/n | Need part # for tension regulator arm shown on page 100 ofs/m. -hq comments: part number is x-3681-493-2. this information is coveredin s/b 221 (12/6/85). |