Thomson Repair Tips
Search: thomson
Results: 227
Results: 227
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| THOMSON |
ICC17
|
Ew faulty | Dl22 byw76 leaky, tl41 bd241c driver u/s, tl42 bc546b u/s, s/c across dl42 caused by iv01 64 pin sm tda8855h jungle chip | ||
| THOMSON |
ICC17
|
Destroys loptrs & e/w unstable | Cl22 22nf 1kv o/c across e/w diode | ||
| THOMSON |
ICC17
|
Dead - no main psu start up | Crack in print front control panel - no supply for st/by led & r/c rx | ||
| THOMSON |
ICC11 72MK89D
|
Luminance lost | Check with scope pin 14 pl/skt bv001. if vid signal missing or crushed check t130, 132 & 134 in if module. if good signal sound check vid signal at tv001 under screen in vid module. if no sig sound tv681 &/or tv682 can be responsible. if sig at tv001 ok, tv002/3 are faulty | ||
| THOMSON |
ICC11 72MK89D
|
Excess brightness with fb lines | Rl128 1m8 in a1 pot divider on dynamic focus module | ||
| THOMSON |
32WT45U
|
Flyback lines then pulsing pic when a1 reduced | Loptx 10675710 | ||
| THOMSON |
32WS83KP
|
Dead & tripping | Ht ok at 95v when lop dis'd - ib01 tea5101b rgb o/p chip on crt base | ||
| THOMSON |
28WF45E
|
No b | No b-y signal. iv100 tda9178 u/s. | ||
| THOMSON |
21CB26VN
|
Dead - psu works on dummy load | Rp531 100r sm o/c (had prev had fop chip if01 & chopper fet tp20 changed) | ||
| THOMSON |
20CB25UT
|
Tv cuts out after 10 seconds - video sect dead | R002 1r o/c on video | ||
| THOMSON |
20CB25UT
|
Int no response to any controls, int no sound or pic at start up | After checking eeprom by replacement discovered micros clock not running - not xtal but 2 x sm caps in xtal osc cct | ||
| THOMSON |
14CB25UT
|
Dead with psu running | Fuse fw002 on video board | ||
| THOMSON |
28WT25ES
ICC17 |
It starts three times and turns off, then the LED flashes twice and stops, flashes seven times and stops. | Zl13 component interrupted, there is no voltage to the vertical ci | Replaced it and kept working | celestino |
| THOMSON COM DVD |
28WT25ES
ICC17 |
It wouldn't start, the LED kept blinking code 27 | Resolved replace zl13 | celestino | |
| NORDMENDE THOMSON |
GALAXI 36
TX805 |
Dead, not even the LED turns on | Resistors rp41 rp42 rp38 | kimen | |
| THOMSON |
32LB130S5
|
Not start goes on and off, after warms up can start ok some time not-dry joint. | Bad soldering on small board 5-volt power supply on ip610 if not help replaced ip610(str a6159). | John Doe | |
| THOMSON |
32WF400G
ICC20 |
It does not turn on, there is a flashing LED followed by four more flashes, I think it is error code 14. | CP130 and CP131 electrolytic capacitors of 220uf 35v. of the voltages ua+ and ua- in poor condition | Kartonnx | |
| THOMSON |
VARIOS
TX805 |
Fountain tries to start but goes down and keeps bouncing | Ptc rp25 with too much consumption | Replace ptc with the same | TECNICA ORIMA |
| THOMSON |
VARIOS
TX805 |
Works well but only in black and white | Replace cc11 | TECNICA ORIMA | |
| THOMSON |
VARIOS
TX805 |
Takes a long time to start | Test voltages on the tp12 transistor if they are lower than 14v | Replace rp41-rp42-rp44 in power supply | TECNICA ORIMA |